Clas Ohlson SST-10 User Manual

English
GREAT BRITAIN • customer service tel: 0845 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
Ver. 20140207
Motion Detector Alarm
Art.no 36-4784 Model SST-10
Please read theentire instruction manual before use and save it for
future reference. Wereserve theright for any errors in text or images
and for making any necessary technical changes to this document.
Ifyou should have any questions concerning technical problems
please contact our Customer Services.
Safety
Note: Thealarm emits anextremely loud signal; ear protection
should be worn during familiarisation exercises and tests in order to
prevent hearing damage.
• The product is only intended for indoor use. Donot expose it
tomoisture.
• Prolonged exposure to thealarm signal can damage your hearing.
• Do not subject thealarm unit to heavy impacts.
Product description
• Alarm unit with PIR motion detector which can be used
wall-mounted or freestanding
• Adjustable wall bracket
• Remote control
Buttons and functions
Alarmunit
Remote control
Pairing thealarm unit and remote control
1. Open thebattery compartment by unscrewing theretaining
screw (4) and sliding thecover down. Insert3×AA/LR6
batteries. Note:Follow thepolarity markings on thebottom of
thebattery compartment. TheLED setting indicator (2) will flash
when thebatteries have been inserted correctly.
2. Press [ LEARN ], immediately point theremote control at thefront
of thealarm unit and press [ ARM ]. Thealarm will emit ashort
signal and theLED indicator will stop flashing to confirm that
theremote has been paired with thealarmunit.
3. Refit thebattery cover and secure it with theretaining screw.
Installation
The alarm unit has adetection range of 6 m straight ahead. Ithas
ahorizontal detection angle of approximately 110º and avertical
detection angle of approximately 70º.
Chimemode
The chime mode is used to notify you when motion is detected in
thedetection zone.
1. Set theChime/Alarm switch on remote control toChime.
2. Point theremote control at thealarm unit and press [ ARM ].
Thechime will sound immediately and from then on whenever
motion is detected.
3. The chime mode can be disarmed by pressing [ DISARM ] on
theremote control.
Panic feature
The alarm can be set off without theneed for motion to have
beendetected.
1. Point theremote control at thealarm unit and hold in both
the[ ARM ] and [ DISARM ] together for two seconds.
2. The panic feature can be disarmed by pressing [ DISARM ] on
theremote control.
Testing themotion detector
Testing theoperation of themotion detector using theremote control in
thealarm mode is best avoided due to thehigh volume. Procedure:
1. Set theChime/Alarm switch on remote control toChime.
2. Point theremote control at thealarm unit and press [ ARM ].
Thechime will soundonce.
3. Wait for 15 seconds and then wave your hand in front of
themotion detector. Ifthechime sounds, thedetector is
operating correctly.
4. The alarm unit can now be set to thealarm mode if desired,
asdescribed in theAlarm mode section above.
Care and maintenance
• Clean theproduct using alightly moistened cloth. Onlyuse mild
detergents, never solvents or corrosive chemicals.
• Remove all thebatteries if theproduct is not to be used for
alongtime.
• Never mix old and new batteries. Changeall batteries at
thesametime.
Troubleshooting guide
The
remote
control
doesn’t
work.
• The battery is flat. Replace thebattery (CR2032).
• Make sure that thebattery is correctly fitted.
Referto thesection Buttons and functions –
Remote control.
• Point theremote control directly at thealarm unit
and make sure that nothing is between them.
• The units have not been paired. Referto thesection
Pairing thealarm unit and remote control.
The alarm
unit is not
working.
• The batteries are flat. Replace with new ones
(3×AA/LR6).
• Make sure that thebatteries are correctly fitted.
Followthemarkings on thebottom of thebattery
compartment.
• The units have not been paired. Referto thesection
Pairing thealarm unit and remote control.
False
alarms are
triggered.
• The alarm unit is poorly positioned (eg in direct
sunlight, in adraught or above aradiator or
other source of heat).
Disposal
This product should be disposed of in accordance with local regulations.
Ifyou are unsure how to proceed, contact your local authority.
1. Motion detector
2. LED setting indicator
3. LED motion detection indicator
4. Battery cover retaining screw
5. [ LEARN ] Button for pairing thealarm unit and remote control
6. Battery compartment
7. LED indicator which flashes when the[ ARM ] or [ DISARM ]
are pressed. Note: TheLED indicator will flash slowly when
thebattery in theremote control begins to lose its charge.
8. [ ARM ] This button arms thealarmunit.
9. [ DISARM ] This button disarms thealarmunit.
The remote control has afactory-fitted battery. Openthebattery
compartment and remove theplastic foil tab from thebattery
terminal to activate theremote control.
Wall bracket
10. Screwholes
11. Alarm unit attachment
1. Wall mounting: Attachthewall bracket to thewall using thetwo
provided screws and wall plugs depending on thesupporting
material. Therecommended installation height is 1.8–2.4m.
Note: Becareful to avoid concealed electrical wiring and water
pipes when drilling or screwing into thewall.
2. Grip thearm of thebracket and attach thealarm unit to it.
Slidethealarm unit into thebracket attachment until it clicks
intoplace.
Operation
Alarmmode
1. Set theChime/Alarm switch on remote control toAlarm.
2. Point theremote control at thealarm unit and press [ ARM ].
Thealarm unit will emit ashort signal and theLED indicator
light will flash. Therewill now be a45-second delay before
theunit is armed. Thedelay gives you time to move out of
thedetectionzone.
3. When motion is detected, thealarm unit will emit ashort
signal and thered LED indicator (3) will flash. Therewill now
be a30-second delay before thealarm sounds. Thesignal
will sound for 30 seconds and then turn off. After15seconds
thealarm will be armed again and if any motion is detected
thealarm cycle will repeat until [ DISARM ] on theremote control
is pressed.
4. The alarm mode can be disarmed by pressing [ DISARM ] on
theremote control.
1
2
3
4
5
6
ARM DISARM
7 8 9
10
11

Clas Ohlson SST-10 Specifications

General

Brand	Clas Ohlson
Model	SST-10
Category	Security System
Language	English