Clas Ohlson SST-10 User Manual

English
GREAT BRITAIN • customer service tel: 0845 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
Ver. 20140207
Motion Detector Alarm
Art.no 36-4784 Model SST-10
Please read theentire instruction manual before use and save it for
future reference. Wereserve theright for any errors in text or images
and for making any necessary technical changes to this document.
Ifyou should have any questions concerning technical problems
please contact our Customer Services.
Safety
Note: Thealarm emits anextremely loud signal; ear protection
should be worn during familiarisation exercises and tests in order to
prevent hearing damage.
• The product is only intended for indoor use. Donot expose it
tomoisture.
• Prolonged exposure to thealarm signal can damage your hearing.
• Do not subject thealarm unit to heavy impacts.
Product description
• Alarm unit with PIR motion detector which can be used
wall-mounted or freestanding
• Adjustable wall bracket
• Remote control
Buttons and functions
Alarmunit
Remote control
Pairing thealarm unit and remote control
1. Open thebattery compartment by unscrewing theretaining
screw (4) and sliding thecover down. Insert3×AA/LR6
batteries. Note:Follow thepolarity markings on thebottom of
thebattery compartment. TheLED setting indicator (2) will flash
when thebatteries have been inserted correctly.
2. Press [ LEARN ], immediately point theremote control at thefront
of thealarm unit and press [ ARM ]. Thealarm will emit ashort
signal and theLED indicator will stop flashing to confirm that
theremote has been paired with thealarmunit.
3. Refit thebattery cover and secure it with theretaining screw.
Installation
The alarm unit has adetection range of 6 m straight ahead. Ithas
ahorizontal detection angle of approximately 110º and avertical
detection angle of approximately 70º.
Chimemode
The chime mode is used to notify you when motion is detected in
thedetection zone.
1. Set theChime/Alarm switch on remote control toChime.
2. Point theremote control at thealarm unit and press [ ARM ].
Thechime will sound immediately and from then on whenever
motion is detected.
3. The chime mode can be disarmed by pressing [ DISARM ] on
theremote control.
Panic feature
The alarm can be set off without theneed for motion to have
beendetected.
1. Point theremote control at thealarm unit and hold in both
the[ ARM ] and [ DISARM ] together for two seconds.
2. The panic feature can be disarmed by pressing [ DISARM ] on
theremote control.
Testing themotion detector
Testing theoperation of themotion detector using theremote control in
thealarm mode is best avoided due to thehigh volume. Procedure:
1. Set theChime/Alarm switch on remote control toChime.
2. Point theremote control at thealarm unit and press [ ARM ].
Thechime will soundonce.
3. Wait for 15 seconds and then wave your hand in front of
themotion detector. Ifthechime sounds, thedetector is
operating correctly.
4. The alarm unit can now be set to thealarm mode if desired,
asdescribed in theAlarm mode section above.
Care and maintenance
• Clean theproduct using alightly moistened cloth. Onlyuse mild
detergents, never solvents or corrosive chemicals.
• Remove all thebatteries if theproduct is not to be used for
alongtime.
• Never mix old and new batteries. Changeall batteries at
thesametime.
Troubleshooting guide
The
remote
control
doesn’t
work.
• The battery is flat. Replace thebattery (CR2032).
• Make sure that thebattery is correctly fitted.
Referto thesection Buttons and functions –
Remote control.
• Point theremote control directly at thealarm unit
and make sure that nothing is between them.
• The units have not been paired. Referto thesection
Pairing thealarm unit and remote control.
The alarm
unit is not
working.
• The batteries are flat. Replace with new ones
(3×AA/LR6).
• Make sure that thebatteries are correctly fitted.
Followthemarkings on thebottom of thebattery
compartment.
• The units have not been paired. Referto thesection
Pairing thealarm unit and remote control.
False
alarms are
triggered.
• The alarm unit is poorly positioned (eg in direct
sunlight, in adraught or above aradiator or
other source of heat).
Disposal
This product should be disposed of in accordance with local regulations.
Ifyou are unsure how to proceed, contact your local authority.
1. Motion detector
2. LED setting indicator
3. LED motion detection indicator
4. Battery cover retaining screw
5. [ LEARN ] Button for pairing thealarm unit and remote control
6. Battery compartment
7. LED indicator which flashes when the[ ARM ] or [ DISARM ]
are pressed. Note: TheLED indicator will flash slowly when
thebattery in theremote control begins to lose its charge.
8. [ ARM ] This button arms thealarmunit.
9. [ DISARM ] This button disarms thealarmunit.
The remote control has afactory-fitted battery. Openthebattery
compartment and remove theplastic foil tab from thebattery
terminal to activate theremote control.
Wall bracket
10. Screwholes
11. Alarm unit attachment
1. Wall mounting: Attachthewall bracket to thewall using thetwo
provided screws and wall plugs depending on thesupporting
material. Therecommended installation height is 1.8–2.4m.
Note: Becareful to avoid concealed electrical wiring and water
pipes when drilling or screwing into thewall.
2. Grip thearm of thebracket and attach thealarm unit to it.
Slidethealarm unit into thebracket attachment until it clicks
intoplace.
Operation
Alarmmode
1. Set theChime/Alarm switch on remote control toAlarm.
2. Point theremote control at thealarm unit and press [ ARM ].
Thealarm unit will emit ashort signal and theLED indicator
light will flash. Therewill now be a45-second delay before
theunit is armed. Thedelay gives you time to move out of
thedetectionzone.
3. When motion is detected, thealarm unit will emit ashort
signal and thered LED indicator (3) will flash. Therewill now
be a30-second delay before thealarm sounds. Thesignal
will sound for 30 seconds and then turn off. After15seconds
thealarm will be armed again and if any motion is detected
thealarm cycle will repeat until [ DISARM ] on theremote control
is pressed.
4. The alarm mode can be disarmed by pressing [ DISARM ] on
theremote control.
1
2
3
4
5
6
ARM DISARM
7 8 9
10
11

Clas Ohlson SST-10 Specifications

General

Type	Wireless
Components	motion detector, door/window sensor, remote control
Power Supply	Batteries (sensors and remote)
Battery Life	Approximately 1 year (sensors and remote)
Installation	Easy, DIY installation

Summary

Safety

Safety Notes

Buttons and Functions

Pairing the Alarm Unit and Remote Control

Pairing Procedure

Step-by-step guide to pair the alarm unit with the remote control, including battery insertion.

Installation

Detection Range

Details the horizontal (110°) and vertical (70°) detection angles and 6m range.

Wall Mounting

Operation

Alarm Mode Operation

Panic Feature

Testing the Motion Detector

Testing Procedure

Troubleshooting Guide

Remote Control Issues

Troubleshooting steps for when the remote control is not working, checking battery and pairing.

Alarm Unit Not Working

Steps to resolve issues with the alarm unit, focusing on batteries and pairing.

False Alarms