GB
46
If you can’t fix the fault yourself, contact your
nearest vendor. Please be aware that any
improper repairs will also invalidate the war-
ranty and additional costs may be incurred.
Disposal
Disposal of the appliance
WARNING! Risk of fire or environ-
mental damage! Avoid damage
caused by leaking fuel: drain the tank
prior to disposal.
This appliance must not be disposed of with
regular household waste! Dispose of the
appliance in the appropriate manner. For
more information, consult your community
waste disposal service.
Disposal of the packaging
The packaging consists of cardboard
and correspondingly marked plastics
that can be recycled.
– Make these materials available
for recycling.
Technical data
Material number 234860
Displacement 144,3 cm³
Rated output 2,3 kW
(2900 min
-1
)
Tank capacity 0,8 l
Motor oil quantity 0,5 l
Working width 46 cm
Cutting height 25–75 mm
Number of stages 7
Volume of collecting
sack
55 l
Weight 22,5 kg
Max. motor speed 2900 min
-1
Sound power level
(L
WA
)*
92,3 dB(A)
(K = 3 dB(A))
Sound pressure level
(L
PA
)*
81,9 dB(A)
(K = 3 dB(A))
Vibration** 4,51 m/s²
(K = 1,5 m/s²)
Spark plug TORCH F5RTC/
F7RTC
*) The noise emission values indicated have been measured
according to a standardized test method and can be used to
compare one power tool with another. The noise emission val-
ues indicated can also be used for a preliminary assessment of
the exposure. Warning: The noise emissions during the actual
use of the power tool may differ from the indicated values,
depending on the way in which the power tool is used, in particu-
lar what type of workpiece is being machined. Safety measures
must be defined to protect the operator, based on an estimation
of the vibration load during actual conditions of use (taking into
consideration all parts of the operating cycle, such as time peri-
ods when the power tool is switched off and time periods when
it is switched on but running without a load).
**) The specified vibration emission value was measured in accord-
ance with a normed test procedure and can be used in order to
compare one tool with another
. The specified vibration emission
value can also be used for an introductory evaluation of the
exposure. The vibration emission value may fluctuate from the
specified value during actual use of the power tool. These fluc-
tuations will depend on the way in which the power tool is used.
Try to keep vibrations to a minimum. One method of reducing
the vibration load is, for example, limiting the length of time you
work with the tool. All parts of the operating cycle must be taken
into account for this purpose (for example, also including times
in which the power tool is switched off and times in which it is
switched on, but is running without load). Determination of vibra-
tion emission values in accordance with EN 60745-1 &
EN 60745-2-13.
Usable fuels and lubricants
NOTICE! Risk of environmental
damage! Fire hazard! Avoid dam-
age caused by leaking fuel: Drain the
tank before disposing of the product.
NOTICE! Risk of product damage!
Never use Bio-Ethanol E85 as fuel!
• Unleaded normal petrol, 90 octane (If
there is no normal petrol available, you
can also use petrol with a higher octane
number
.)
• Motor oil: SAE 10W
-30
Instructions for fuels
Fuels with ethanol mixtures (e. g. E10)
Fuels with high ethanol mixture are more
aggressive than fuels with less or without eth-
anol mixture. Possibly painted surfaces and
plastics can be strongly af
fected or damaged.
Moreover, fuel with ethanol mixture strongly
reacts to influential factors such as light rays,
temperature and storage time. Hence, these
Incorrect fuel? Empty tank and fill up with the
correct fuel.
Abnormal noise. Screws/parts looses? Re-tighten the screws.
Foreign objects in the blade? Remove foreign objects.
Blade damaged? Grind or exchange the blade.
Cut quality insufficient. Blade dull?
Fault/malfunction Cause Remedy
Material number 234860
To Next Page
Loading...
Need help?
General
