Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
Operating Your Radio
49
Nothing Comes Close to a Cobra
®
Advanced Operation
48
English
Advanced Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
Operating Your Radio
Scan Modes
A signal on any channel will stop the scan for 10 seconds
to allow you to listen to the traffic on that location. After 10
seconds, the radio will resume scanning.
Press the Channel Up/Down button to resume scanning before
the 10-second pause has completed or to change the scan
direction.
VHF Channel Scan
During Channel Scan mode, the radio will rapidly switch from
channel to channel through all the channels.
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
NOTE
The radio must be squelched for Channel Scan mode
to function. See page 28 for Squelch procedure.
To Enter Marine Scan:
1. From Marine or GMRS Standby mode, press the SCAN
button. The radio will immediately begin to scan the
entire channel map selected in the active channel map.
CHANNEL SCAN will display on the matrix.
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
NOTE
If Priority 16 feature has been selected, channel 16 will
checked frequently for activity to insure you will not miss
any calls.
2. To EXIT Channel Scan mode, press the SCAN or PTT
button again. The SCAN icon will disappear from the LCD
and the radio will return to Marine or GMRS Standby
mode.
MEMSAMEVOX HI
ROG
VHF
GMRS
T
R
X
U
SCAN Button
SAMELO
VHF
U
A
Scan Display
MEMSAMEVOX HI
ROG
VHF
GMRS
T
R
X
U
Channel Up/Down Buttons
To Enter Memory Location Scan:
1. From Marine or GMRS Standby mode, press the MEM/
ESC button.
2. Press the SCAN button. The radio will immediately begin
to scan all pre-assigned memory channels. The MEM
icon will show on the LCD, and MEM CHAN SCAN will
display on the matrix along with the memory location.
3. To EXIT Memory Location Scan mode, press the SCAN
or PTT button again. The MEM icon will disappear from
the LCD and the radio will return to Marine or GMRS
Standby mode.
GMRS Scan
In GMRS mode, there are 3 types of scans - all GMRS channels,
CTCSS tones (on the selected channel) and DCS codes (on the
selected channel).
To Enter the GMRS Scans:
1. Successive press and release of the SCAN button will
toggle betwen all channel scan, CTCSS tone scan and
DCS code scan.
2. Press and hold the SCAN button to start the
selected scan.
3. To exit a GMRS scan, press the MEM/ESC button or
PTT.
MEMSAMEVOX HI
ROG
VHF
GMRS
T
R
X
U
MEM/ESC Button
Memory Channel Scan
Memory Location Scan
During Memory Location Scan mode, the radio will rapidly scan
through all pre-assigned memory channels.
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
NOTE
The radio must be squelched for Memory Location Scan
mode to function. See page 18 for Squelch procedure.
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
NOTE
If there are fewer than two (2) memory locations
programmed in the radio, the Memory Location Scan
option will not be available. To program at least two (2)
memory locations, see page 34.
LO
GMRS
Scan All Schannels
Scan CTCSS
LO
GMRS
Scan DCS
To Next Page
Loading...
