EN
4.2.4 Push backward and forward again to confirm the seat is locked firmly.
4.3 Crotch belt adjustment
The crotch belt is position at the inner slot when you get the seat. Once you feel that the crotch belt is
too tight for your child. Please 07 adjust as follow:
4.3.1 Pull up the cover at the front of your seat, (fig.?).
4.3.2 Lift the metal part and through into the outer slot (fig.8,9). 4.3.3. Then
pull out at under side then insert into inner slot(fig10,11). 4.3.4. Now through the metal part into the
other slot at the top surface
of the seat (fig.12).
4.3.5. through the other slot again (fig13).
4.3.6. Flatthe metal partto finish (fig14).
4.4 Adjust the height of shoulder belt.
Notice: Ambra child seat's harness have 2 height position, the top of the shoulder belt must be parallel
or a little higher than the child's shoulders. That can provide the effective protect for your child at
collision.
Follow the step as bellow.
4.4.1. Relax the harness before adjust the height: One hand press down the center adjuster button
(part no.10 page 01) at the same time with the other hand hold the shoulder belt (part no.03 page
01) and pull back. (Fig. 15)
4.4.2. Press on the release button (part no.23) and separate the buckle tongue, (part no.24 page 01).
(Fig. 16)
4.4.3.1nsert the both tongue through the slots
(Fig. 17)
4.4.4. At the rear side insert the both tongue into other slots, (Fig. 18)
4.4.5. Then combine the two tongue belt and insert into the buckle housing
(part no.22 page 01) again to finish the adjustment. (Fig. 19,20)
5 Seat selection and adjustment
5.1 Adjusting the car seat 08
Put the Ambra on the vehicle seat, and the child' face toward to the rear of vehicle driving direction.
ensures that the bottom surface of the seat is flat to the vehicle seat surface and the front of Ambra
just touch against vehicle backrest
surface. (Fig. 21).
Otherwise is not OK (Fig. 22).
5.2 Seat installation
The child restraint system Ambra can be installed in vehicles on any seat suitable for use in the listed
vehicles fitted with 3-point with retractor safety-belts, approved to ECE Regulation No. 16 or other
equivalent standards. (Fig. 23).
And must not at any time be fitted using only a 2-point lap belt. (Fig. 24).
If the car manufacturer allows child restraint systems on the passenger seat, the seat should be
moved to the position maximum back .(Fig. 25).
We suggest always to install this child seat at the rear seat of the vehicle. This will be more safety for
your child.
Important:
Check if the vehicle buckle has interference with child seat, try to another seat. (If this is the case will
cannot fix the seat well). Please contact our customer service department if you are in any doubt.
Always using the rear seats of your vehicle even if your highway code permits the use
on the front seat. Check your highway code as this regulation may vary according to the country.lt is
better to assemble your seat at side pavement.
6 Installation in vehicle
6.1.Seat installation: Place the child seat to the rear seat in the vehicle, Let the bottom of the seat
against vehicle seat surface, and the front of the seat touched vehicle seat backrest. (fig.26)
6.2.Then Extend the vehicle belt longer enough,Insert it from the slot at the front of the seat, then
through it into the slot to the other side. (fig. 27).
6.3.1nsert the buckle tongue (part no.12 page01) into the vehicle buckle (part no.13), and hear a
"click". (fig. 28).
6.4.1 nsert the diagonal belt into the slot at the rear or Ambra (part no.19 page 01). (fig. 29).
To Next Page
Loading...
