EN
6.5.Pull the diagonal belt at the top of the vehicle buckle make the belt tight. (fig. 30).
6.6.Then pull the diagonal belt at the top of the seat as arrow indicate. As tight as you can. (fig. 30).
6.71nstallation of child: Refer the (section 7) to fix your child carefully to finish the installation.
Finally check the child seat is fix stable on the vehicle seat. If you find any shake
that you must tighten the belt again until the child seat is tight enough. lmpor tant: Misuse the child car
seat will reduce the protect
that the seat provides.
Check the belt at the right position and is tight enough at all of the position, and no twist is present.
7 Securing the child
When your child's weight is between 0-13kg.lt need to fix your child by the
3-point harness. According the follow step :
7.1.Relax the harness before adjust the height, one hand press down the center adjuster (part no.10
page 01), at the same time the other hand hold the shoulder belt (part no.03 page 01) and pull back.
(fig.31).
7.2.Relax the buckle: push down the release button on the buckle (part no.23 page 01), the buckle
tongue will jump out. then put the harness to the both side of seat. (fig 32).
7.3.Put your child on the child seat, let the buckle (part no.22 page 01) is on the front of your child's
crotch. Make your child's arms through the should belt (part no.03 page 01), the shoulder belt and the
shoulder pad just on the top of your child's shoulder. (fig 33).
Adjust the harness and headrest height refer to (chapter 4.4). The top of the shoulder belt must be
parallel or a little higher than the child's shoulders. Too high or too low is not suggested. (fig 33).
7.4. Reassemble buckle (part no.22 page 01) until you hear a "click". (fig.34).
7.5. Pull back the adjust belt (part no.07 page 01) make the harness tight. To be ensure
there should not be more than a fingers width between the harness and your child. It's most
importance of ensuring that any lap strap is worn low down, so that the pelvis is firmly engaged, shall
be stressed. (fig.35).
Notice: If the harness is too tight, please relax it then adjust it again.
8. Removing and replacing the cover
The fabric cover on this seat can be remove for washing,It just need release the plastic clip and pull
out at the fringe of the seat. (fig.36) After washing you can assemble it to the
seat again.
The seat cover is a part of the child seat, the child restraint must not be used without the cover. The
seat cover should not be replaced with any other than the one recommended by the manufacturer,
because the cover constitutes an integral part of the restraint performance.
Suggestion: Do not wash the fabric frequent. It must assemble again as original state after washing.
To replace the cover,follow the steps of removing the cover in reverse order
9 Washing and maintenance
Check if there is any part has missed or broken,if this is the case Do not use the seat again.
9.1 Fabric:
Fabric can wash by the temperature less than 300,Then dry by nature condition.
9.2 Belt and plastic:
Wash fabric with warm water and mild soap,do not use solvents or high-potency soap: Do not
remove,move or change fabric and original fabric or any part of the harness.
9.3 Buckle:
Always check that there is no food debris or other such matter in the harness buckle. This may affect
the correct function of the buckle please clean it by warm water. You can hear a "click" when the
buckle function is normal.
10. Steps to take after an accident
After an accident with an impact speed greater than 10 km/h,the child restraint system must be sent
back to the manufacturer without fail,to be checked for possible damages and replaced at no charge if
deemed necessary.
To Next Page
Loading...
