4
Dim Operation
The DEFENDER features a low power "Dimming" mode. Dimming will be controlled by applying +12V by way of the appropriate wire
(Blue) in the wire harness/wire list. When DIM is engaged, the TriCore light heads will operate in a reduced power mode.
Note: The corner mounted TriCore light heads are excepted from this function and will not dim.
Please contact the factory if more information is needed concerning the dimming mode.
The Dim setting reduces the light output of emergency warning lights reducing the effectiveness of
them especially in brightly lit areas. Failure to use adequate light for the circumstances can cause
motorists to fail to see the emergency vehicle and lead to serious personal injury or death. Never
use the DIM setting in a brightly lit area. Use of the DIM setting may cause emergency lights to not
comply with applicable emergency warning light standards. Use caution when using the DIM setting to
assure that motorists can clearly see the emergency vehicle.
WARNING!
This Product contains high intensity TriCore devices. To prevent eye damage,
DO NOT stare into light beam at close range.
WARNING!
LED ArrowStik feature
The DEFENDER has a programmable ArrowStik feature integrated into the light bar that operates independently of the other
features. Refer to the ArrowStik Programming section of this manual for detailed information on pattern selection and
operation instruction.
Selecting Flash Patterns
The Pattern Select wire is the BLK/RED wire in the sixteen conductor lightbar control cable and is activated by momentarily touching
the wire to +power.
STEP 1
Power-up the lightbar and select the Level-1 ash mode by applying +power to the GRN/BLK wire in the 16 conductor control cable.
STEP 2
Observe the ashing pattern operation and determine which pattern is in operation for Level-1. Refer to Table 1. This table shows the
available ash patterns. Note: the Factory Default is different and identied in the table for each of the ash mode Levels (L1, L2, L3).
Once the ash pattern has been determined, proceed to Step 3.
STEP 3
Scroll to the next ash pattern by momentarily holding the Pattern Select wire (BLK/RED) to +power for ~1 sec, until the TriCore light
heads switch ash patterns, and then releasing it. This will step to the next pattern in numbered order as listed in Table 1 for the
selected 3-Level mode. The new pattern is automatically stored each time. Repeat this procedure for Level-2 and Level-3.
Note: All control inputs are +power enabled.
Control Input Function Denitions
Wire Color Function Description
GRN/BLK Level 1 Level 1 Emergency Mode
WHT/BLK Level 2 Level 2 Emergency Mode
RED/BLK Level 3 Level 3 Emergency Mode
ORG/BLK Takedown lights Takedown Lights Steady Burn (overrides Takedown Flash)
BLU/BLK Rear Cut-Off Blacks-Out Rear Facing heads
GRN/WHT Front Cut-Off Blacks-Out Front Facing heads
RED/WHT Right Alley Light Right Alley Steady Burn (overrides Alley Light Flash)
BLK/WHT Left Alley Light Left Alley Steady Burn (overrides Alley Light Flash)
WHT ArrowStik Flash ArrowStik Flash (overrides L1, L2 & L3 for rear of light bar)
BLK/RED** Pattern Select Pattern Select for ArrowStik, L1, L2 & L3, (enables test mode)
BLK Takedown Flash Enables Takedown Lights Wig/Wag Flash
RED* ArrowStik Left Left ArrowStik (overrides L1, L2 & L3 for rear of light bar)
GRN Cruise Lights End heads only (overridden by all other functions)
ORG* ArrowStik Right Right ArrowStik (overrides L1, L2 & L3 for rear of light bar)
BLU Light bar DIM Sets heads to Dim mode
BLU/WHT Alley Light Flash Enables Alley Light Wig/Wag Flash
See "Notes" Next Page
To Next Page
Need help?
General
