CommScope BSAMNT-3 User Manual

Part Lists
M8 screw
two hole plate
7
• Bracket edges parallel to each other.
(fully collapsed position)
Pre-assembly of Downtilt Brackets by Kit Vendor
(Not applicable for BSAMNT-F)
5
15
6
16
3
4
17
M10 screw
SCISSOR GASKET
ITEM NO. DESCRIPTION
BSAMNT-3
QUANTITY
BSAMNT-M/-MH
QUANTITY
BSAMNT-F
QUANTITY
1 PIPECLAMP BRACKET, NO FLANGE 4 2 4
2 BRACKET, PIPE CLAMP INTERFACE 2 1 2
3 NOTCHED BRACKET 1 1 -
4 BRACKET 1 1 -
5 SCR,HCS,HEX,M8X25,10mm UNT,SST,PASS 2 2 -
6 WSHR,BELLE,M8,16-8.2-1.5,SST,PASS 2 2 -
7 PLATE, TWO HOLES 2 2 -
8 NUT,HEX,M10,STL,GALV 12 8 8
9 WSHR,LK,SPLT,M10,STL,GALV 6 4 4
10 SCR,HCS,HEX,M10X40,STL,GALV 6 4 4
11 NUT,HEX,M12,STL,GALV 12 6 12
12 WSHR,FLT,M12,13X24X2.5,STL,GALV 4 2 4
13 WSHR,LK,SPLT,M12,STL,GALV 4 2 4
14 CARRIAGE BOLT,WITH HEAT SHRINK 4 2 4
15 SCR,HCS,HEX,M10X25,10mm UNT,SST,PASS 2 2 -
16 WSHR,BELLE,M10,20-10.2-1.6,SST,PASS 2 2 -
17 SCISSOR GASKET 2 2 -
18 WSHR,FLAT,M16,17.5x30x2.5,SST 4 2 4
19 ISOLATOR 4 2 4
Mounting Kits For Wide Panel Antennas
BSAMNT-3, BSAMNT-M & BSAMNT-MH & BSAMNT-F: Mounting systems for cylindrical pipe
installations (60-115 mm pipe diameter) for heavy duty applications
This document explains how to install an antenna using a BSAMNT mount kit. Antennas with two mount points
will use BSAMNT-3 or BSAMNT-F. Antennas with three mount points will also include the BSAMNT-M or
BSAMNT-MH. The antenna mechanical tilt can not be adjusted if BSAMNT-F is used.
639840 Revision J, February 2020
Page 1 of 4
www.commscope.com
© 2020 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639840 J (02/20)

CommScope BSAMNT-3 Specifications

General

Product Type	Antenna Mount
Includes	Mounting hardware
Color	Gray
Mounting Type	Pole Mount
Material Type	Steel
Mounting	Pole
Material	Steel
Compatibility	Various Antenna Models

Summary

Mounting Kits For Wide Panel Antennas

Pre-assembly of Downtilt Brackets

Guides the pre-assembly of downtilt brackets by the kit vendor.

Pre-assembly of Pipe Bracket

Explains the pre-assembly of the pipe bracket by the field installer for different mount kits.

General Safety Warning

Warns about loosening/removing bolts attaching the mounting plate to the antenna.

Top / Middle Mount Installations

Details the installation process for top or middle mounting configurations.

Bottom Mount Installation

Details the installation process for bottom mounting configurations.

Adjusting Antenna Tilt - 2 POINT MOUNT

Instructions for adjusting the antenna tilt for 2-point mount systems.

Adjusting Antenna Tilt - 3 POINT MOUNT

Instructions for adjusting the antenna tilt for 3-point mount systems.

Remote Electrical Tilt Connection

Information regarding the AISG connector and its proper tightening torque.

RF Cable Connection

Guidelines for connecting RF cables and tightening connectors to avoid damage.

General Safety Notice

Provides essential safety precautions for installation and maintenance personnel.