Confer Plastics 635-52

To Next Page

SAFETY RULES

* One person on the ladder at a time

* Ladder MUST be installed per manufacturer’s instructions

* DANGER: No Jumping or Diving from ladder

* Face ladder when entering and leaving pool

* To prevent entrapment or drowning —

DO NOT swim through, behind or around ladder

* Ladder to be used as a swimming pool ladder only.

* Weight limit - 250 lbs maximum

* Warning: Exceeding the maximum weight restriction

may cause the ladder to fail.

* Consult your local Building Department before

installation of your pool and equipment.

* DANGER:

Use a cordless drill for assembly and installation

Never use an electric drill in or around the pool.

CONFER PLASTICS, INC.

LIMITED, PRO-RATED WARRANTY

Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in workmanship for one year from

date of purchase. After the first year the cost to replace a part is as follows:

MODEL #635-52

Year - 20%

Year - 40%

Year - 60%

Year - 80%

Plus shipping/handling

Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name, address, and daytime phone number. You

will be notified of cost to replace part.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

MODEL 635-52

ALL PLASTIC INPOOL LADDER

ASSEMBLY AND INSTRUCTION MANUAL

CONFER LADDERS ARE DESIGNED FOR EASE OF ASSEMBLY AND ARE CONSTRUCTED

OF MAINTENANCE-FREE, NON-CORROSIVE RESINS AND MATERIALS.

Note: WARRANTY ON PAGE 4. PLEASE SAVE THIS BOOKLET AND YOUR WARRANTY.

MADE IN THE U.S.A. BY:

CP 635-52 10/07Printed in U.S.A.

97 Witmer Road

North Tonawanda, NY 14120-2421

Toll Free U.S. 866-396-2968

Tel: 716-283-1826 / FAX: 716-283-3249

www.conferladders.com

• 635-52 Fits Decks 46"-56"

• Easy Assembly

• Adjustable Handrail

Mounting System

Made in U.S.A. by

SAVE THESE INSTRUCTIONS

DEALER/INSTALLER: GIVE TO HOMEOWNER

*Model 635-52 is a

straight up-and-down

ladder and should be

installed 3" to 6" from

the pool wall.

Note: 10 Lbs of

sand required

(See Step 2)

DO NOT RETURN DEFECTIVE PART TO DEALER

The defective part should be returned, postpaid, to:

Confer Plastics, Inc.

97 Witmer Road

North Tonawanda, N.Y. 14120-2421

of current parts

list price

SAND

Confer A frame 635-52_R6:Confer A frame 635-52_R1 10/11/07 12:06 PM Page 1

Need help?

Do you have a question about the Confer Plastics 635-52 and is the answer not in the manual?

Summary

Model 635-52 Assembly Instructions

Step 1: Install Threaded Cap

Install the threaded cap over the bottom drain hole of the ladder.

Step 2: Fill Ladder Legs

Pour 5 lbs of sand into each ladder leg and fill the remainder with water.

Step 3: Position Handrails

Slide the handrails onto the legs without securing them at this stage.

Step 4: Insert Adjustable Tubes

Push the adjustable tubes through the mounting blocks, applying lubricant if needed.

Step 5: Place Ladder and Position Blocks

Place the ladder in the pool and position mounting blocks on the deck.

Step 6: Secure Mounting Blocks and Handrails

Fasten mounting blocks to the deck and attach handrails using screws.

Important Safety Information

Check Parts and Follow Instructions

Verify all parts are present before assembly and follow all instructions sequentially.

Safe Assembly and Use

Ensure safe assembly and use; the manufacturer is not liable for improper installation.

Additional Accessories

Skim-It

A skimmer extension that guides debris into your pool skimmer.

EB 100-3 Riser

Used to raise the ladder when the deck is higher than the pool.

DK300 Deck Kit

Provides an extra step at the top of the ladder, preventing deck damage.