Control 4 C4-KP2-Z User Manual (English)

To Next Page

Wireless 2, 3, and 6-Button

Keypad Installation Guide

Supported Models and Requirements

• C4-KP2-ZWireless2-ButtonKeypad

• C4-KP3-ZWireless3-ButtonKeypad

• C4-KP6-ZWireless6-ButtonKeypad

Specications

ThisControl4

multi-buttonKeypadisintendedforuseinaControl4system.Itinstalls

inastandardwallboxusingtypicalwiringstandardsandcommunicatestotheControl4

systemusingawirelessconnection.Thespecicationsaredescribednext.

Power:

120VAC+/-10%50/60Hz

400mW

ThisdevicerequiresaneutralAC

connection.

Supported Load Types:

NotApplicable.Thisdevicedoesnotdirectlycontrol

aload.

Communications:

IEEE802.15.4,2.4GHz,15-channel,spread

spectrumradio

Warnings and Considerations

WARNING! Installinaccordancewithallnationalandlocalelectricalcodes.

WARNING! ImproperuseorinstallationcancauseSERIOUSINJURY,

DEATHorLOSS/DAMAGEOFPROPERTY.

WARNING!Ifyouareunsureaboutanypartoftheseinstructions,consulta

qualiedelectrician.

WARNING!ToreducetheriskofSERIOUSINJURYorDEATH,turnOFF

localelectricalpowerbeforeinstallingthisproduct,andbeforeinstalling,

removing,orreplacingkeycaps.

IMPORTANT!Usingthisproductinamannerotherthanoutlinedinthis

documentvoidsyourwarranty.Further,Control4isNOTliableforany

damageincurredwiththemisuseofthisproduct.See“Limited2-Year

Warranty.”

IMPORTANT! DoNOTuseapowerscrewdrivertoinstallthisdevice.Ifyou

do,youmayovertightenthescrewsandstripthem.

Installation Instructions

Ensurethatthelocationandintendedusemeetthefollowingcriteria:

• Whenreplacingatraditional3-wayswitch,refertothe“Two-Location”sample

wiringcongurationsprovidedinthefollowingdocuments:

Wireless Dimmer Installation Guide

Wireless Switch Installation Guide

• Installinaccordancewithallnationalandlocalelectricalcodes.

• TherequiredwallboxsizeisspeciedbytheNEC(NationalElectricalCode).

Theinternalwallboxvolumeoccupiedbythismulti-buttonkeypadis5.0cubic

inches.

• Therangeandperformanceofthewirelesscontrolsystemishighlydependent

onthefollowing:(1)distancebetweendevices;(2)layoutofthehome;(3)walls

separatingdevices;and(4)electricalequipmentlocatedneardevices.

• Ifyouareplanningtouseengravedkeycapsfor3-Buttonand6-ButtonKey-

pads,DONOTcontinueuntilyouhavereadthe“ReplaceKeycaps”section.

• Ifinstallingamulti-buttonkeypadinamulti-ganginstallation,DONOTcontinue

untilyouhavereadthe“Multi-GangInstallations”section.

4. Ifyouneedto“ReplaceKeycaps”ordo“Multi-GangInstallations,”refertothose

sectionsbeforecontinuing.

WARNING!Aswithanyelectricaldevice,improperuseorinstallationcan

causeSERIOUSINJURYorDEATH.Itisimportantthatyouunderstandthe

particularwiringcongurationofyourinstallationbeforeproceeding.Note:The

wallboxwiringshowninthisdocumentisanexample.Yourwirecolorsand

functionsmaydiffer.IfyouarenotsurewhichwiresaretheHot,Neutral,and

Groundwires,haveatrainedelectriciandotheinstallation.

Fitthewiresbackintothewallbox.Bendthewiresinazigzag

patternsothattheyeasilyfoldintothewallbox.

IfyouareusingtheControl4push-on(screwless)wallplate

thatshippedwithyourmulti-buttonKeypad:

Operation and Conguration

Oninitialpowerup,theunitwillashtheRed/Green/Blue(RGB)LEDswhichcanbe

programmedwithdifferentcolorsfordifferentstatesorcolorpreferences.Tosetupthis

KeypadforusewithaControl4system,refertotheComposer Pro User Guide.

Troubleshooting

IfoneormoreLightEmittingDiodes(LEDs)arenotlit:

• EnsurecircuitbreakerisnotturnedOFFortripped.

• Checkforproperwiring,suchastheexampleinStep5.Youmayalsoneedtocontact

atrainedelectrician.

• Forhelpontheinstallationoroperationofthisproduct,emailorcalltheControl4

TechnicalSupportCenter.Pleaseprovideyourexactmodelnumber.Contact

support@control4.comorseethewebsitewww.control4.com.

IMPORTANT!Notgroundingthisproductaccordingtotheprecedingmay

resultinaninstallationlessimmunetodamagecausedbyelectrical

disturbances,suchaslightning,andvoidthewarranty.

IMPORTANT! Thisisanelectronicdevicewithintricatecomponents.Handle

andinstallwithcare!

WARNING!ToreducetheriskofSERIOUSINJURYor

DEATH,turnOFFlocalelectricalpowerbeforeinstallingthis

product.

2. Turnoffthelocalelectricalpowerbyeitherswitchingoffthecircuitbreakerorremov-

ingthefusefromthefusebox.ToensurethewiresdoNOThavepowerrunningto

them,useaninductivevoltagedetector.

3. Prepareeachwire.Wireinsulationshouldbe

strippedback5/8ofaninchfromthewireend

(asshown).

5. Identifyandconnectthemulti-button

Keypadwirestothewallboxwiresusing

thewirenuts.

Note:Wallboxwirescandifferdepend-

inguponhowtheboxwaswiredbyyour

electrician.

Towirethemulti-buttonKeypad,connect

andcapthewireswithawirenutas

indicatedinthefollowingtable.

Multi-Button Keypad Wires

(2,3, or 6-Button)

Wires in Wall Box

White(neutral) White(neutral)

Green(ground) Green(ground)

Black(hot) Black(hot)

Alignthemulti-buttonKeypadtothewallboxandfasten

itwithscrews.Tightenthescrewsuntilthebacksideof

themetalyokeplateisevenwiththewallsurface,butno

further.Overtighteningcanwarpthemulti-buttonKeypad

andcausemechanicalmalfunction.

Withthewallplate’sremovalslotfacingdown,pushthe

wallplateontotheKeypad’sblackplasticsub-plate.

8. IfyouareusingaDecora-stylescrew-onwallplate:

Removethemulti-buttonKeypad’sblackplasticsub-plate

andstoreitforfutureuse(incaseyoulaterdecidetouse

theControl4wallplate).

Alignthemulti-buttonKeypadtothewallboxandfastenit

withscrews.

Fastenthewallplatetothemulti-buttonKeypaditwith

screws.

10.

TurnONpoweratthecircuitbreakerorreplacethefusefrom

thefusebox.

EnsurethatallLEDsonthefrontarelit.

Replace Keycaps

Note:Appliesto3-buttonand6-ButtonKeypadsonly.

WARNING!ToreducetheriskofSERIOUSINJURYorDEATH,turnOFFthe

localelectricalpowerbeforeinstalling,removing,orreplacingkeycaps.

Control4offersstandardengravedkeycapsandcustomengravedkeycaps(bothsold

separately)toenableyoutopersonalize3-Buttonand6-ButtonKeypads.

Note:Customengravingisnotavailablefor2-ButtonKeypads.

Ifyouarereplacingkeycaps:

1. Turnoffthelocalelectricalpower.

2. Removethescrew-lessorscrew-onwallplatefromthe

multi-buttonKeypad.

3. Removetheblackplasticsub-platefromthemulti-button

Keypadbyremovingthescrewatthetopandbottomofthe

device.

4. PinchbothsidesoftheKeycapretaineratbothends—

workingrstatthetop,thenthebottom—togentlyremove

theretainer.DONOTprytheretaineroffwithascrew

driver.

5. RemovethedefaultKeycapsfromtheKeycapretainerand

replaceeachonewiththeengravedKeycapofyourchoice.

BesuretoplacetheLEDatthetop.

6. Carefullysnaptheretainerbackintoplace,takingcarenot

todamagetheretainerclips.

7. Reattachthesub-platewiththescrews.Reattachthewall

plate.

Multi-Gang Installations

If using a Decora-style screw-on multi-gang wall plate:

Removetheblackplasticsub-platefromeachdevice,justasyouwouldforasinglede-

vice(seeStep8in“InstallationInstructions”),andstoreitforfutureuseincaseyoulater

decidetousetheControl4wallplate.

TIP: Foreaseofinstallation,eachdevice’syokeplatemustbeevenand

alignedinaatplanesothatthemulti-gangsub-platecansitatagainstall

ofthedevices.Thiscanbeaccomplishedbyinitiallynotscrewingthedevices

tightlyagainstthewallbox,leavingabout1/8ofaninchgapbetweenthewall

andtheyokeplates.Thisallowseachdevicetomoveandconformtothesub-

plate.Usingthenewscrewssuppliedwiththemulti-gangsub-plate,securethe

multi-gangsub-platetoalldevicestocreateasinglestructure.Thensecure

thestructurebytighteningthewallboxscrewstheremaining1/8ofaninch.

Donotover-tightenanyofthescrewsoryouwillmis-aligntheatplaneofthe

multi-gangwallplate.

Multi-ganginstallationsarecongurationsinwhichtwo(2)ormoredevicesareinstalled

side-by-sideinthesamewallbox.Formulti-ganginstallations:

If using a Control4 push-on (screw-less) multi-gang wall plate:

Removetheindividualblackplasticsub-platefromeachdeviceandreplacethemwiththe

multi-gangsub-platethatshippedwithyourControl4multi-gangwallplate.Theuseofthe

multi-gangsub-plateinherentlyalignsandspaceseachdeviceproperly.

Care and Cleaning

• DoNOTpaintthemulti-buttonkeypadoritswallplate.

• DoNOTuseanychemicalcleanerstocleanthemulti-buttonkeypad.

• Cleansurfacewithasoftdampclothasneeded.

Regulatory Compliance

FCC

FCCID:R33C4KP3Zforthe2and3-ButtonKeypad

FCCID:R33C4KP6Zforthe6-ButtonKeypad

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowing

twoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevice

mustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired

operationofthisdevice.

Sonfonctionnementestsoumisauxdeuxconditionssuivantes:(1)cetappareilnedoit

pascauserd’interférencesnuisibleset(2)cetappareildoitacceptertouteinterférence

reçue,ycomprislesinterférencesquipeuventcauserunmauvaisfonctionnementdu

dispositif.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

device,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequip-

mentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledand

usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocom-

munications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionrecep-

tion,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencour-

agedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:•

• Reorientorrelocatethereceivingantenna.•Increasetheseparationbetweenthe

equipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich

thereceiverisconnected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

IMPORTANT!Anychangesormodicationsnotexpresslyapprovedbythe

partyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatethis

equipment.

ETL Statement

ETLControlNumber:3129831

ThisproducthasbeentestedbyETLandwasfoundtocomplywiththeStandardfor

SafetyforIndustrialControlEquipment:

• UL244A3rdedition:2003;StandardforSolidStateControls

forAppliances.

• CSAStandardC22.2#14-05:2005;IndustrialControlEquipment.

Industry Canada

IC:7848A-C4KP3Zforthe2and3-ButtonKeypad

IC:7848A-C4KP6Zforthe6-ButtonKeypad

ThisClassBdigitalapparatuscomplieswithCanadaICES-003.

CetappareilnumériquedelaclasseBestconformeàlanormeNMB-003duCanada.

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterfer-

enceand(2)thisdevicemustacceptanyinterference,includinginterferencethatmay

causeundesiredoperationofthedevice.

L’opérationestsujetteauxdeuxconditionssuivantes:(1)cedispositifpeutnepascauser

l’interférenceet(2)cedispositifdoitacceptern’importequelleinterférence,ycompris

l’interférencequipeutcauserlefonctionnementpeudésirédudispositif.

WARNING!WARNING!GroundtheWirelessKeypadinaccordancewiththe

NationalElectricCode(NEC)requirements.AlthoughtheKeypad’saluminum

yokeplateandgreengroundwirearedirectlybondedtogetherinsidethe

keypad,DONOTrelysolelyupontheyokeplate’scontactwithametalwall

boxforadequategrounding.UsetheKeypad’sgroundwiretomakeasecure

connectiontothesafetygroundoftheelectricalsystem.

Control 4 C4-KP2-Z User Manual

Control 4 C4-KP2-Z Specifications

Summary

Installation Instructions

Power Off and Wire Preparation

Connect Keypad Wires

Supported Models and Requirements

Specifications

Warnings and Considerations

Electrical Code Compliance

Safety Precautions

Consult a Qualified Electrician

Power Interruption for Installation

Warranty and Product Handling

Operation and Configuration

Initial Power Up and LEDs

Troubleshooting

LEDs Not Lit

Care and Cleaning

Regulatory Compliance

ETL Statement

Industry Canada

Recycling

Limited 2-Year Warranty

About this Document

Related product manuals

Brand	Control 4
Model	C4-KP2-Z
Category	Keypad
Language	English