COVANA OASIS - User Manual

Other manuals for COVANA OASIS

User Manual32 pages

Installation Manual62 pages

Questions and Answers

C
campbellscottSep 16, 2025
How to fix unevenly positioned posts on my COVANA Hot Tub cover?
- J
  Jessica OdonnellSep 16, 2025
  Unevenly positioned posts on your COVANA Hot Tub cover can occur if the post screws are missing or loose. Lower the cover completely and screw in the self-drilling screws as shown in the installation manual. Additionally, check if a drive shaft has fallen off and re-install it, or if a chain skipped during operation and needs replacement. Finally, inspect the spring pin at the bottom of each jack for breakage and replace if necessary.
T
Tracie GilbertAug 25, 2025
Why won't my COVANA OASIS Hot Tub elevate or lower, even though the motor is humming?
- G
  Gina ScottAug 25, 2025
  If your COVANA Hot Tub motor is humming but not elevating or lowering, it could be due to frozen posts. Try the following: * Remove any snow and ice from the Covana roof and release the shades/screens from their lower restraining brackets. * Turn the key off and on several times to try to free up the frozen post. * Slap the side of each post to help break loose any ice or frost. * Apply a silicone-based lubricant to the telescoping aluminum sleeves. * Ensure a proper seal by checking for leaks around the posts when the jets and air are on and the roof is lowered. If there’s a leak, loosen the outside post clamp, push down on the roof until the leak stops, and then retighten the clamp and reinsert the safety screw. * Perform the jack greasing procedure.
J
Jamie SmithAug 25, 2025
What to do if my COVANA OASIS Hot Tub cover doesn't raise or lower?
- S
  Sara SampsonAug 26, 2025
  If your COVANA Hot Tub cover isn't moving and the motor is silent, the GFCI might be tripped. Try resetting the GFCI. Also, ensure that the power source is properly connected and enabled.
P
Peter HintonAug 26, 2025
Why won't my COVANA OASIS cover fully raise or lower, even with the motor humming?
- A
  Amanda PinedaAug 27, 2025
  If your COVANA Hot Tub cover motor is humming but there's limited movement, the posts might be frozen. Use methanol to free any ice buildup. Also, check for and remove any obstructions on top of the cover. The jack assemblies may be jammed; try greasing them. Also ensure that the posts are not obstructed.
J
Joshua WilliamsSep 18, 2025
What to do if the magnetic plate on my COVANA OASIS Hot Tub is not holding in place?
- S
  Samuel Wheeler DDSSep 18, 2025
  If the magnetic plate on your COVANA Hot Tub is not holding, there may be excessive tension in the Constant Tension System (CTS) 70. Lift the side of the outer shell where the cable exits from the inner shell; remove the CTS 70 from the steel frame and grease the interior surfaces. Also, check that the CTS 70 pulley carrier can travel the length of the CTS 70 without interfering with any object.
N
Natasha OlsenSep 23, 2025
Why is the magnetic plate on my COVANA Spa Accessories not holding in place?
- B
  Brittany WilliamsSep 23, 2025
  If the magnetic plate on your COVANA Spa Accessories isn't holding, it could be due to excessive tension in the Constant Tension System (CTS) 70. To resolve this, lift the side of the outer shell where the cable exits from the inner shell, remove the CTS 70 from the steel frame, and grease the interior surfaces.
J
Jessica AllenSep 8, 2025
Why does my COVANA Outdoor Furnishing cover raise but not lower?
- J
  Johnny StevensonSep 9, 2025
  If your COVANA Outdoor Furnishing cover raises but does not lower, it could be due to a few potential issues. The cam plate may be incorrectly positioned or missing, or the key switch may be faulty. The limit switches might not be moving properly. A certified electrician should open the operator and check for faulty up and down limit switches. Remember to remove power before performing any electrical work, and inspect the terminals for corrosion, cleaning them if necessary.
C
Catherine JimenezSep 9, 2025
Why are the posts on my COVANA Outdoor Furnishing not equally positioned?
- R
  Richard KiddSep 9, 2025
  If the posts of your COVANA Outdoor Furnishing are not equally positioned, it could be because the post screws attached to the inner sleeve are missing or have loosened. In this case, lower the cover completely and screw in the self-drilling screws. Another reason might be that a drive shaft has fallen off, so re-install any fallen drive shaft. A chain might have skipped during operation, requiring you to replace any broken chain. Finally, a spring pin at the bottom of a jack could be broken, so replace any missing or broken spring pin.
R
Richard WilsonSep 3, 2025
What to do if my COVANA Spa Accessories cover raises but does not lower?
- D
  David FernandezSep 3, 2025
  If your COVANA Spa Accessories cover raises but doesn't lower, consider these potential issues: * The cam plate might be incorrectly positioned or missing. Open the operator and check for faulty up and down limit switches. * The key switch on the keyswitch could be faulty. Open the keyswitch and check for a faulty switch. * The limit switches might not be moving properly. Open the operator and check for faulty up and down limit switches.
H
Heidi PierceSep 1, 2025
What to do if COVANA Spa Accessories cover does not raise or lower, and motor is humming?
- T
  Thomas StewartSep 1, 2025
  If your COVANA Spa Accessories cover is not raising or lowering but the motor is humming, there might be a few reasons: * The posts may be frozen. Use methanol to free any ice buildup. * The jack assemblies might be jammed. Remove any debris from the top of the cover. * There may be too much debris on the cover. Remove all debris from the top of the cover. * The power source could be disconnected. Verify that the power source is enabled.

Summary

Important Safety Information

General Safety Guidelines

General safety guidelines, including warnings, cautions, and notes.

Safety Hazards and Warnings

Operational Precautions

Electrical Safety and Modifications

Keyswitch Positioning Requirements

Labeling and Identification Guide

Electrocution Risk and Cable Labels

Explains safety labels, electrocution risks, and cable information.

Specific Safety Labels

Installation Procedure Overview

Tools Required for Installation

Lists necessary tools for installation.

Preparation for Installation

Spa Location Considerations

Foundation Preparation Guidelines

Delivery and Handling Procedures

Crate Securing and Unpacking

Assembly and Lifting Mechanism (Part 1)

Lifting Mechanism Installation (Part 1)

Jack and Frame Installation Steps

Drive Shaft Installation Guide

U-Frame and Coupler Installation

Short U-Frame and Jack Screw Procedures

Barrel Nut and Sleeve Installation

Lifting Mechanism Installation (Part 2)

Testing the Cover Operation

Seal Installation Procedure

Electrical Connections Guide

Risk of Electrocution Warnings

Grounding and Power Supply Connections

Limit Switch Adjustment Procedures

Cam Plate Removal for Adjustment

Cam Wheels Adjustment

Operating the Covana Cover

Raising;Lowering with Key Switch

Step-by-step guide to operate the cover using the keyswitch.

Manual Operation of the Cover

Wiring Diagram (North America, Lights)

Schematic Diagram (North America)

Wiring Diagram (Europe, No Lights)

Schematic Diagram (Europe)

Wiring Diagram (Europe, Lights)

Schematic Diagram (Europe, Lights)

Maintenance Procedures

Winterizing the Cover

Post Greasing Maintenance

Sliding Parts Greasing

Chain Lubrication Procedure

Electrical and Operation Specifications

Electrical Specifications

Lists voltage, GFCI, and current draw requirements for NA and EU models.

Operation Limitations

Troubleshooting Common Issues

Troubleshooting Cover Movement

Troubleshooting Cover Appearance

COVANA OASIS Specifications

General

Weatherproof	Yes
Voltage	240V
Amperage	50A
Shell Material	Acrylic
Cover Type	Hard Cover
Material	Acrylic
Locking Mechanism	Yes
LED Lighting	Multi-Color
Water Capacity	350 Gallons
Pumps	2
Heater	4 kW
Filtration	Dual filtration system
Ozonator	Yes
Cabinet Material	Synthetic
Cover	Hard Cover
Warranty	5 Years