Craftsman 154.37297 - User Manual

Questions and Answers

C
Carly ClarkAug 5, 2025
Why Craftsman 154.37297 Lawn Mower engine fails to start?
- M
  Mary BaileyAug 5, 2025
  There are several reasons why your Craftsman Lawn Mower engine might fail to start: * The blade control may be disengaged; make sure to engage it. * The spark plug boot might be disconnected; connect the wire to the spark plug boot. * The fuel tank could be empty or contain stale fuel; fill it with clean, fresh gasoline. * The engine may not be primed (if equipped with a primer); prime the engine as instructed in the Operation section. * The spark plug could be faulty; clean, adjust the gap, or replace it. * The engine might be flooded; wait a few minutes before restarting. * The fuel line could be blocked; contact your Sears Parts & Repair Center to have the fuel line cleaned.
J
John HuberAug 11, 2025
Why does my Craftsman Lawn Mower engine run erratically?
- A
  Adrienne ShafferAug 11, 2025
  An erratic running engine in your Craftsman Lawn Mower can be caused by several factors: * A loose spark plug boot; connect and tighten it. * Stale fuel; replace it with clean, fresh gasoline. * A plugged vent in the gas cap; clear the vent. * Water or dirt in the fuel system; run the engine until it stops from lack of fuel, then refill with fresh fuel. * A dirty air cleaner; refer to the Air Cleaner section in Engine Maintenance. * A blocked fuel line; contact your Sears Parts & Repair Center to have it cleaned.
T
twatsonAug 17, 2025
Why Craftsman Lawn Mower idles poorly?
- M
  Mike BassAug 17, 2025
  A Craftsman Lawn Mower idling poorly might be due to: * A fouled or faulty spark plug, or a gap that's too wide; reset the gap or replace the spark plug. * A dirty air cleaner; refer to the Air Cleaner section in Engine Maintenance.
D
Dawn HallAug 23, 2025
What to do if Craftsman 154.37297 Lawn Mower engine overheats?
- M
  Michael JohnstonAug 23, 2025
  If your Craftsman Lawn Mower engine overheats: * Check the engine oil level and fill the crankcase with the proper oil if it's low. * Ensure there is no restriction to air flow; clean the area around and on top of the engine.
W
William MillerAug 29, 2025
What causes excessive vibration in Craftsman 154.37297 Lawn Mower?
- R
  ronaldsullivanAug 29, 2025
  Excessive vibration in your Craftsman Lawn Mower can be attributed to: * A loose or unbalanced cutting blade; tighten the blade and adapter, and balance the blade. * A bent cutting blade; replace the blade.

Summary

Safety Instructions

General Operation and Warnings

Covers general operation, danger symbols, and warnings.

California Proposition 65

Details specific warnings related to California regulations.

Slope Gauge

Using the Slope Gauge

Instructions on how to use the provided gauge to check slope steepness.

Assembly

Carton Opening and Handle Attachment

Steps for unpacking the mower and attaching the handle assembly.

Side Discharge Cover and Height Adjustment

Details on attaching the side discharge cover and adjusting cutting height.

Operation

Mower Controls and Components

Identifies and explains key controls like blade control, starter, and primer.

Starting, Stopping, and Safe Mowing

Instructions for starting and stopping the engine, and safe usage practices.

Service and Maintenance

Maintenance Schedule and General Advice

Outlines the recommended maintenance schedule and general tips.

Blade Care and Balancing

Procedures for inspecting, removing, and servicing the mower blade.

Off-Season Storage

Preparing Engine and Mower for Storage

Guidelines for properly storing the mower during off-season.

Troubleshooting

Common Problems and Solutions

Addresses common engine and operational issues with remedies.

Emission Control System Warranty

Owner Responsibilities and Warranty Terms

Details owner obligations, warranty coverage, and exclusions.

Parts and Service Contact

Ordering Replacement Parts or Service

Provides contact information for ordering parts or scheduling repairs.

Craftsman 154.37297 Specifications

General

Power Source	Gasoline
Engine Type	4-Cycle
Cutting Positions	6
Cutting Width	21 inches
Cutting Height	1.25-3.75 inches
Wheel Size (Front)	8 inches
Wheel Size (Rear)	11 inches