Craftsman 247.203750 - User Manual

Craftsman 247.203750

62 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operator’s Manual

T1600 LAWN TRACTOR

19 HP, Variation Speed

46” Deck

Model No. 247.203750

®

For answers to your questions about

this product, call:

1-888-331-4569

Craftsman Tractor Help Line

7 am - 7 pm CT, Mon. - Sun.

This product has a low emission engine which operates differently

from previously built engines. Before you start the engine, read and

understand this Operator’s Manual.

• Espanol, P. 31

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our website: www.craftsman.com

CAUTION

Before using this equipment,

read this manual and follow

all safety rules and operating

instructions.

Form No. 769-09450

(November 19, 2013)

Table of Contents

Questions and Answers

N
Nathan DavilaAug 20, 2025
What to do if Craftsman Lawn Mower engine runs erratically?
- H
  Heather HendrixAug 21, 2025
  If your Craftsman Lawn Mower engine is running erratically, it could be due to: * Running with the CHOKE activated: Deactivate the CHOKE. * Loose spark plug wire(s): Connect the spark plug wire(s). * Blocked fuel line or stale fuel: Replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. * Plugged vent in the gas cap: Clear the vent or replace the cap if it's damaged. * Water or dirt in the fuel system: Drain the fuel tank and refill it with clean, fresh gasoline. * Dirty air cleaner: Replace the air cleaner paper element or clean the foam pre-cleaner, if equipped.
K
Kaitlin CollinsAug 23, 2025
Why Craftsman 247.203750 engine overheats?
- N
  natashasavageAug 23, 2025
  Your Craftsman Lawn Mower engine may overheat due to: * Low engine oil level: Fill the crankcase with the proper amount and weight of oil. * Restricted airflow: Clean grass clippings and debris from around the engine’s cooling fins and housing.
R
robertpruittAug 26, 2025
Why Craftsman 247.203750 has uneven cut?
- R
  Robert GibsonAug 26, 2025
  An uneven cut with your Craftsman Lawn Mower can be caused by: * Deck not leveled properly: Perform a side-to-side deck adjustment. * Dull blade: Sharpen or replace the blade. * Uneven tire pressure: Check the tire pressure in all four tires.
J
Jessica FisherAug 27, 2025
What to do if Craftsman 247.203750 engine idles rough?
- J
  Jocelyn StrongAug 28, 2025
  If your Craftsman Lawn Mower engine idles roughly, it could be due to: * Spark plug fouled, faulty, or gap too wide: Replace the spark plug and set the plug gap. * Dirty air cleaner: Replace the air cleaner element and/or clean the pre-cleaner.
J
Joshua BradleyAug 30, 2025
How to fix uneven cut with Craftsman 247.203750?
- C
  carriestevensAug 30, 2025
  An uneven cut with your Craftsman Lawn Mower can be caused by several factors. First, the deck might not be leveled properly, so perform a side-to-side deck adjustment. A dull blade can also contribute to an uneven cut, so sharpen or replace the blade. Finally, check the tire pressure in all four tires, as uneven tire pressure can also cause this issue.
N
nicholscrystalSep 1, 2025
What to do if Craftsman 247.203750 Lawn Mower is not mulching grass?
- H
  Hannah HarrisSep 1, 2025
  If your Craftsman Lawn Mower isn't mulching grass effectively, consider these points: * Engine speed is too low: Place the throttle in the FAST (rabbit) position. * Grass is wet: Avoid mulching when the grass is wet. * Grass is excessively high: Mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. * Blade is dull: Sharpen or replace the blade.
B
Brett AguirreSep 4, 2025
Why Craftsman Lawn Mower has excessive vibration?
- E
  Ellen WalkerSep 4, 2025
  Excessive vibration in your Craftsman Lawn Mower could stem from: * Cutting blade loose or unbalanced: Tighten the blade and spindle. * Damaged or bent cutting blade: Replace the blade.
L
lisa14Sep 6, 2025
What causes Craftsman 247.203750 engine to hesitate at high RPM?
- S
  Sarah FuentesSep 6, 2025
  The Craftsman Lawn Mower engine hesitates at high RPM because the spark plug gap is too close. To fix this, remove the spark plug and reset the gap.
C
Carol MerrittSep 8, 2025
Why Craftsman 247.203750 is not mulching grass?
- E
  eric80Sep 8, 2025
  Your Craftsman Lawn Mower might not be mulching grass effectively because the engine speed is too low, so place the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. A dull blade will also prevent effective mulching, so sharpen or replace the blade.
J
julie92Sep 12, 2025
What causes excessive vibration in Craftsman 247.203750 Lawn Mower?
- J
  Jonathan JonesSep 12, 2025
  Excessive vibration in your Craftsman Lawn Mower may be caused by a loose or unbalanced cutting blade. Try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, requiring replacement.

Craftsman 247.203750 Specifications

General

Brand	Craftsman
Model	247.203750
Category	Lawn Mower
Language	English

Related product manuals

Preview: Craftsman 247.203753

Craftsman 247.203753

Preview: Craftsman T1600 247.203751

Craftsman T1600 247.203751

Craftsman 247.20375 series

Craftsman 247.20370

Craftsman 247.203724

Preview: Craftsman 247.203791

Craftsman 247.203791

Preview: Craftsman T1000 247.203701

Craftsman T1000 247.203701

Preview: Craftsman T1600 247.203744

Craftsman T1600 247.203744

Preview: Craftsman T1400 247.203734

Craftsman T1400 247.203734

Preview: Craftsman T1600 247.203743

Craftsman T1600 247.203743

Preview: Craftsman T1200 247.203770

Craftsman T1200 247.203770

Preview: Craftsman T1200 247.203723

Craftsman T1200 247.203723