EasyManua.ls Logo

Craftsman 247.203753 - User Manual

Craftsman 247.203753
64 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operator’s Manual
T1600 LAWN TRACTOR
19 HP, Variation Speed
46” Deck
Model No. 247.203753
For answers to your questions about
this product, call:
1-888-331-4569
Customer Care Hot Line
This product has a low emission engine which operates differently
from previously built engines. Before you start the engine, read and
understand this Operator’s Manual.
• Espanol, P. 31
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
Visit our website: www.craftsman.com
CAUTION
Before using this equipment,
read this manual and follow
all safety rules and operating
instructions.
Form No. 769-09450B
(December 17, 2014)

Table of Contents

Questions and Answers

  • B
    Brandon NewmanAug 21, 2025
    What to do if Craftsman 247.203753 engine runs erratically?
    • C
      carlascottAug 21, 2025
      If your Craftsman Lawn Mower engine is running erratically, it could be due to: * Running with the CHOKE activated: Deactivate the CHOKE. * Loose spark plug wire(s): Connect the spark plug wire(s). * Blocked fuel line or stale fuel: Replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. * Plugged vent in the gas cap: Clear the vent or replace the cap if it's damaged. * Water or dirt in the fuel system: Drain the fuel tank and refill it with clean, fresh gasoline. * Dirty air cleaner: Replace the air cleaner paper element or clean the foam pre-cleaner, if equipped.
  • R
    Renee MartinezAug 23, 2025
    Why Craftsman 247.203753 Lawn Mower engine overheats?
    • Y
      yvonnegrayAug 23, 2025
      Your Craftsman Lawn Mower engine may overheat due to: * Low engine oil level: Fill the crankcase with the proper amount and weight of oil. * Restricted airflow: Clean grass clippings and debris from around the engine’s cooling fins and housing.
  • G
    Gloria WarrenAug 26, 2025
    Why Craftsman Lawn Mower has uneven cut?
    • L
      Lauren PetersonAug 26, 2025
      An uneven cut with your Craftsman Lawn Mower can be caused by: * Deck not leveled properly: Perform a side-to-side deck adjustment. * Dull blade: Sharpen or replace the blade. * Uneven tire pressure: Check the tire pressure in all four tires.
  • S
    swallaceAug 27, 2025
    What to do if Craftsman Lawn Mower engine idles rough?
    • R
      russelljessicaAug 28, 2025
      If your Craftsman Lawn Mower engine idles roughly, it could be due to: * Spark plug fouled, faulty, or gap too wide: Replace the spark plug and set the plug gap. * Dirty air cleaner: Replace the air cleaner element and/or clean the pre-cleaner.
  • D
    Daniel RodriguezAug 30, 2025
    How to fix uneven cut with Craftsman 247.203753?
    • U
      ubradleyAug 30, 2025
      An uneven cut with your Craftsman Lawn Mower can be caused by several factors. First, the deck might not be leveled properly, so perform a side-to-side deck adjustment. A dull blade can also contribute to an uneven cut, so sharpen or replace the blade. Finally, check the tire pressure in all four tires, as uneven tire pressure can also cause this issue.
  • M
    Monica KingSep 1, 2025
    What to do if Craftsman 247.203753 is not mulching grass?
    • C
      Claudia McclainSep 1, 2025
      If your Craftsman Lawn Mower isn't mulching grass effectively, consider these points: * Engine speed is too low: Place the throttle in the FAST (rabbit) position. * Grass is wet: Avoid mulching when the grass is wet. * Grass is excessively high: Mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. * Blade is dull: Sharpen or replace the blade.
  • C
    Cindy LittleSep 4, 2025
    Why Craftsman 247.203753 has excessive vibration?
    • C
      Cynthia CopelandSep 4, 2025
      Excessive vibration in your Craftsman Lawn Mower could stem from: * Cutting blade loose or unbalanced: Tighten the blade and spindle. * Damaged or bent cutting blade: Replace the blade.
  • L
    Laura StephensSep 6, 2025
    What causes Craftsman Lawn Mower engine to hesitate at high RPM?
    • A
      Andrea AguilarSep 6, 2025
      The Craftsman Lawn Mower engine hesitates at high RPM because the spark plug gap is too close. To fix this, remove the spark plug and reset the gap.
  • D
    David GrossSep 8, 2025
    Why Craftsman 247.203753 Lawn Mower is not mulching grass?
    • S
      Sydney HarveySep 8, 2025
      Your Craftsman Lawn Mower might not be mulching grass effectively because the engine speed is too low, so place the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. A dull blade will also prevent effective mulching, so sharpen or replace the blade.
  • K
    kevin66Sep 12, 2025
    What causes excessive vibration in Craftsman Lawn Mower?
    • Z
      Zachary GarciaSep 12, 2025
      Excessive vibration in your Craftsman Lawn Mower may be caused by a loose or unbalanced cutting blade. Try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, requiring replacement.

Craftsman 247.203753 Specifications

General IconGeneral
BrandCraftsman
Model247.203753
CategoryLawn Mower
Engine Displacement159cc
Cutting Width21 inches
Cutting Height1.25 - 3.75 inches
Cutting Height Positions6
Starter TypeRecoil
Drive TypeSelf-Propelled
Speed SettingsVariable
Mulching CapabilityYes
Bagging CapabilityYes
Side Discharge CapabilityYes
Wheel Size8 inches (front), 11 inches (rear)

Related product manuals