To Next PageTo Next PageHow to fix uneven cut with Craftsman 247.20375 Lawn Mower?
An uneven cut with your Craftsman Lawn Mower can be caused by several factors. First, the deck might not be leveled properly, so perform a side-to-side deck adjustment. A dull blade can also contribute to an uneven cut, so sharpen or replace the blade. Finally, check the tire pressure in all four tires, as uneven tire pressure can also cause this issue.
Why is my Craftsman 247.20375 engine overheating?
Your Craftsman Lawn Mower engine may be overheating due to a low engine oil level. Fill the crankcase with the proper amount and weight of oil. Another cause could be restricted airflow. Clean grass clippings and debris from around the engine’s cooling fins and housing.
What to do if Craftsman Lawn Mower engine idles rough?
If your Craftsman Lawn Mower engine idles rough, it could be due to a spark plug issue. The spark plug might be fouled, faulty, or have a gap that's too wide. Try replacing the spark plug and setting the correct gap. Another potential cause is a dirty air cleaner. In this case, replace the air cleaner element and/or clean the pre-cleaner.
What to do if Craftsman 247.20375 engine runs erratically?
If your Craftsman Lawn Mower engine is running erratically, it could be due to several reasons. First, check if the choke is activated and deactivate it. Next, ensure the spark plug wires are securely connected. A blocked fuel line or stale fuel could also be the culprit; in this case, replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. Additionally, check if the vent in the gas cap is plugged and clear it, or replace the cap if damaged. Water or dirt in the fuel system can also cause this issue, so drain the fuel tank and refill with clean, fresh gasoline. Lastly, a dirty air cleaner can lead to erratic engine performance, so replace the air cleaner paper element or clean the foam pre-cleaner if your mower is equipped with one.
Why Craftsman 247.20375 is not mulching grass?
Your Craftsman Lawn Mower might not be mulching grass effectively because the engine speed is too low, so place the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a high cutting height, then mow again at the desired height, or make a narrower cutting swath. A dull blade will also prevent effective mulching, so sharpen or replace the blade.
What causes excessive vibration in Craftsman 247.20375 Lawn Mower?
Excessive vibration in your Craftsman Lawn Mower may be caused by a loose or unbalanced cutting blade. Try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, requiring replacement.
Why Craftsman 247.20375 engine hesitates at high RPM?
If your Craftsman Lawn Mower engine hesitates at high RPM, it could be due to the spark plug gap being too close. Remove the spark plug and reset the gap.
General| Brand | Craftsman |
|---|---|
| Category | Lawn Mower |
| Cutting Width | 21 inches |
| Cutting Height | 1.25 - 3.75 inches |
| Deck Material | Steel |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Oil Capacity | 20 oz |
| Model | 247.20375 |
| Engine Type | Gasoline |
| Wheel Size | 7 inches front, 8 inches rear |
| Starter Type | Recoil |
| Fuel Tank Capacity | 0.5 gallons |
| Warranty | 2 years limited |
General safety rules, operating instructions, warnings, and cautions for safe use.
Safety guidelines for slopes, children, and towing operations.
Step-by-step instructions for using the slope gauge to measure incline angles safely.
Identifies and explains key controls like throttle, speed lever, and parking brake.
Procedures for starting, stopping, and using ignition modes safely.
Operating speed controls, drive pedals, and shift levers for various transmissions.
Guidelines for slope operation, parking, and blade engagement safety.
Schedule of recommended maintenance tasks based on operating hours.
Common causes and remedies for the engine failing to start.
