EasyManua.ls Logo

Craftsman 247.203723 - User Manual

Craftsman 247.203723
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operator’s Manual
T1200 LAWN TRACTOR
420cc, Variation Speed
42” Deck
Model No. 247.203723
For answers to your questions about
this product, call:
1-888-331-4569
Craftsman Customer Care Hot Line
This product has a low emission engine which operates differently
from previously built engines. Before you start the engine, read and
understand this Operator’s Manual.
• Espanol, P. 36
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
Visit our website: www.craftsman.com
CAUTION
Before using this equipment,
read this manual and follow
all safety rules and operating
instructions.
Form No. 769-09448C
(January 19, 2015)

Table of Contents

Questions and Answers

  • Z
    Zachary RoseSep 12, 2025
    Why is my Craftsman 247.203723 not mulching grass?
    • P
      Paul Conner DDSSep 12, 2025
      If your Craftsman Lawn Mower isn't mulching grass properly, consider these potential causes: * The engine speed might be too low. Place the throttle in the FAST (rabbit) position. * The grass might be wet. Avoid mulching when the grass is wet. * The grass might be excessively high. Mow once at a high cutting height, then mow again at the desired height or make a narrower cutting swath. * The blade might be dull. Sharpen or replace the blade.
  • K
    Katie ScottAug 26, 2025
    What causes an uneven cut with a Craftsman 247.203723?
    • M
      Michele McclureAug 27, 2025
      If your Craftsman Lawn Mower is producing an uneven cut, you should first perform a side-to-side deck adjustment to ensure it is leveled correctly. Next, check the blade; sharpen or replace it if it's dull. Finally, verify that the tire pressure is consistent in all four tires.
  • J
    Justin NelsonAug 28, 2025
    What to do if Craftsman Lawn Mower engine runs erratically?
    • A
      angela83Aug 28, 2025
      If your Craftsman Lawn Mower engine is running erratically, it could be due to several reasons. First, check if the choke is activated and deactivate it. Next, ensure the spark plug wires are securely connected. A blocked fuel line or stale fuel could also be the culprit; in this case, replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. Additionally, check if the vent in the gas cap is plugged and clear it, or replace the cap if damaged. Water or dirt in the fuel system can also cause this issue, so drain the fuel tank and refill with clean, fresh gasoline. Lastly, a dirty air cleaner can lead to erratic engine performance, so replace the air cleaner paper element or clean the foam pre-cleaner if your mower is equipped with one.
  • N
    Nancy ReillyAug 29, 2025
    How to fix uneven cut with Craftsman Lawn Mower?
    • J
      James WalkerAug 29, 2025
      An uneven cut with your Craftsman Lawn Mower can be caused by several factors. First, the deck might not be leveled properly, so perform a side-to-side deck adjustment. A dull blade can also contribute to an uneven cut, so sharpen or replace the blade. Finally, check the tire pressure in all four tires, as uneven tire pressure can also cause this issue.
  • A
    anne52Aug 30, 2025
    What to do if Craftsman 247.203723 Lawn Mower engine idles rough?
    • J
      James WatsonAug 31, 2025
      If your Craftsman Lawn Mower engine idles rough, it could be due to a spark plug issue. The spark plug might be fouled, faulty, or have a gap that's too wide. Try replacing the spark plug and setting the correct gap. Another potential cause is a dirty air cleaner. In this case, replace the air cleaner element and/or clean the pre-cleaner.
  • W
    William DoyleNov 22, 2025
    Why won't my Craftsman 247.203723 Lawn Mower start?
    • R
      rebekah53Nov 22, 2025
      If your Craftsman Lawn Mower engine fails to start, there are several potential causes: * The PTO/Blade Engage lever might be engaged. Ensure it is in the disengaged (OFF) position. * The parking brake might not be engaged. Engage the parking brake. * Spark plug wires might be disconnected. Connect the wires to the spark plugs. * The Throttle/Choke control lever might not be in the correct starting position. Place it in the FAST position. * The choke might not be activated. Move the Throttle/Choke lever into the Choke position. * The fuel tank might be empty or contain stale fuel. Fill it with clean, fresh gasoline (less than 30 days old). * The fuel line might be blocked. Replace the fuel line and fuel filter. * The spark plugs might be faulty. Clean, adjust the gap, or r...
  • S
    Sheila DodsonSep 22, 2025
    What to do if my Craftsman 247.203723 Lawn Mower has excessive vibration?
    • J
      Juan HarrisSep 22, 2025
      If your Craftsman Lawn Mower is vibrating excessively, tighten the blade and spindle first. If the vibration continues, inspect the cutting blade for damage or bending and replace it if necessary.
  • J
    Jordan WilliamsNov 21, 2025
    Why Craftsman 247.203723 engine fails to start?
    • T
      Theresa BarronNov 21, 2025
      Your Craftsman Lawn Mower engine might fail to start due to several reasons: * The PTO/Blade Engage lever might be engaged: place it in the disengaged (OFF) position. * The parking brake might not be engaged: engage the parking brake. * Spark plug wires might be disconnected: connect the wires to the spark plugs. * The throttle/choke control lever might not be in the correct starting position: place the lever into the FAST position. * The choke might not be activated: move the throttle/choke lever into the Choke position. * The fuel tank might be empty or contain stale fuel: fill the tank with clean, fresh gas (less than 30 days old). * The fuel line might be blocked: replace the fuel line and fuel filter. * The spark plugs might be faulty: clean, adjust the gap, or replac...
  • A
    Aimee HardySep 10, 2025
    Why Craftsman 247.203723 Lawn Mower engine hesitates at high RPM?
    • K
      Kimberly BrownSep 10, 2025
      If your Craftsman Lawn Mower engine hesitates at high RPM, it could be due to the spark plug gap being too close. Remove the spark plug and reset the gap.
  • R
    Richard OlsonSep 7, 2025
    What causes excessive vibration in Craftsman 247.203723 Lawn Mower?
    • K
      Kimberly ParkSep 7, 2025
      Excessive vibration in your Craftsman Lawn Mower may be caused by a loose or unbalanced cutting blade. Try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, requiring replacement.

Craftsman 247.203723 Specifications

General IconGeneral
BrandCraftsman
Model247.203723
CategoryLawn Mower
LanguageEnglish

Related product manuals