To Next PageTo Next PageWhy does my Craftsman 247.375910 idle poorly?
Poor idling in your Craftsman Lawn Mower can be attributed to a spark plug that is fouled, faulty, or has a gap that is too wide; reset the gap or replace the spark plug.
Why my Craftsman 247.375910 Lawn Mower engine fails to start?
If your Craftsman Lawn Mower engine won't start, several factors could be the cause. First, make sure the blade control is engaged. Check that the spark plug boot is connected securely. The fuel tank may be empty or contain stale fuel, so fill it with clean, fresh gasoline. If your mower has a primer, prime the engine as instructed in the Operation section. Inspect the spark plug; it may need cleaning, gap adjustment, or replacement. If the engine is flooded, wait a few minutes before attempting to restart it. Finally, a blocked fuel line could be the issue; in this case, contact your Sears Parts & Repair Center to have the fuel line cleaned.
What to do if my Craftsman 247.375910 will not self propel?
If your Craftsman Lawn Mower won't self-propel, there are a few things to inspect. Make sure the belt is properly installed on the pulleys and moves freely. Debris might be clogging the drive mechanism; stop the engine, disconnect the spark plug boot, and clean out any debris. Check the belt for damage or wear and replace it if needed. Finally, the drive control may be out of adjustment.
Why does my Craftsman Lawn Mower leave an uneven cut?
An uneven cut from your Craftsman Lawn Mower is likely due to a dull blade. Sharpen or replace the blade to resolve this.
Why Craftsman Lawn Mower engine runs erratic?
If your Craftsman Lawn Mower engine is running erratically, start by checking the spark plug boot to ensure it's connected and tightened. Stale fuel can also cause this issue, so refill the tank with clean, fresh gasoline. Make sure the vent in the gas cap isn't plugged; clear it if necessary. Water or dirt in the fuel system can also lead to erratic running; run the engine until it stops from lack of fuel, then refill with fresh fuel. A dirty air cleaner could be the culprit. Finally, a blocked fuel line could be the issue; in this case, contact your Sears Parts & Repair Center to have the fuel line cleaned.
Why Craftsman Lawn Mower will not self propel?
If your Craftsman Lawn Mower won't self-propel, first check the belt to ensure it's properly installed on the pulleys and moving correctly. Debris clogging the drive operation can also be a cause; stop the engine, disconnect the spark plug boot, and clean out any debris. Inspect the belt for damage or wear and replace it if necessary. Finally, the drive control may be out of adjustment; in this case, you should adjust the drive control.
How to fix excessive vibration in Craftsman 247.375910 Lawn Mower?
Excessive vibration in your Craftsman Lawn Mower can be due to a loose or unbalanced cutting blade. Tighten the blade and adapter, and balance the blade. Another cause could be a bent cutting blade, which would require replacement.
Why does my Craftsman 247.375910 Lawn Mower occasionally skip or hesitate?
Occasional skipping or hesitation in your Craftsman Lawn Mower may occur if the spark plug gap is too close. Adjust the gap to the correct setting.
Why is my Craftsman 247.375910 vibrating excessively?
Excessive vibration in your Craftsman Lawn Mower can be due to a loose or unbalanced cutting blade; tighten the blade and adapter and balance the blade. Alternatively, the cutting blade might be bent and need replacement.
Why is my Craftsman 247.375910 Lawn Mower engine overheating?
If your Craftsman Lawn Mower engine is overheating, check the engine oil level and fill the crankcase with the proper oil if it's low. Also, ensure that there is no restriction to airflow around the engine by cleaning the area around and on top of the engine.
General| Brand | Craftsman |
|---|---|
| Model | 247.375910 |
| Category | Lawn Mower |
| Language | English |
Instructions for operating the mower safely, including operator responsibilities and area inspection.
Guidelines for safe mowing on slopes, including maximum angle and mowing direction.
Safe practices for handling gasoline, including storage, fueling, and avoiding ignition sources.
Explanation of the blade control and premium drive control functions for operating the mower.
Instructions on how to start the mower's engine using the recoil starter.
Procedures for filling the engine with gasoline and oil, including checking oil level.
Detailed steps for checking the engine oil level using the dipstick.
Specifications for usable gasoline and safety warnings for refueling.
Step-by-step guide on how to start and stop the mower's engine safely.
A schedule outlining required maintenance tasks based on time or hours of use.
Regular checking and changing of engine oil to maintain engine health.
Troubleshooting common problems like engine failure to start or erratic running.
Diagnosing and resolving issues like engine overheating or occasional skipping.
Solutions for problems such as poor engine idling or excessive vibration during operation.
