To Next PageTo Next Page
Need help?Do you have a question about the Craftsman 25411 and is the answer not in the manual?
General| Power Source | Gas |
|---|---|
| Cutting Height Positions | 6 |
| Mulching Capability | Yes |
| Side Discharge | Yes |
| Cutting Width | 21 inches |
| Cutting Height | 1.25 to 3.75 inches |
| Wheel Size | 7 inches front, 8 inches rear |
Read and understand these instructions carefully before using the machine.
Details the process of assembling parts for use.
Explains the basic functions and descriptions of the machine.
Outlines necessary steps and checks before operating the machine.
Provides instructions and guidelines for operating the tractor.
Covers routine maintenance and adjustments for the machine.
Offers solutions for common problems encountered with the machine.
Provides guidance on how to properly store the machine.
Emphasizes the importance of operator training and familiarity with controls.
Details essential preparation steps before operating the mower.
Provides guidelines and safety precautions for operating the mower.
Instructions for mounting the steering wheel.
Details on installing the steering extension shaft.
Guidance on installing and adjusting the tractor seat.
Instructions for assembling the grass bagger.
Guidance on adjusting the bagger for proper function and appearance.
Steps for adjusting the bagger horizontally.
Steps for adjusting the bagger vertically.
Identifies and locates the various control levers and switches on the tractor.
Instructions on how to start the engine safely, ensuring correct lever positions.
Explains the four positions of the motion control lever for forward, reverse, and neutral operation.
Details how to engage and disengage the cutting unit drive.
Explains how to quickly raise and lower the cutting unit for obstacles and transport.
Describes the four positions of the ignition key: OFF, ROS ON, ON, START.
Explains how to engage and disengage the parking brake.
Explains how to tow or move the tractor without the engine using the free-wheel control.
Explains how to use the choke control for cold and warm engine starts.
Guides on using the choke for cold engine starts.
Instructions for adjusting the gas control for warm engines.
Details on turning the ignition key to start the engine and proper procedure if it doesn't start.
Instructions for returning the ignition key to ON and setting the gas control after starting.
Specific cold starting procedures for hydrostatic transmissions.
Instructions for purging the transmission fluid before first use or after service.
Explains safety features like operator presence and reverse operation systems.
Provides instructions on lowering the cutting unit, releasing pedals, and choosing driving speed.
Explains the Reverse Operation System (ROS) and its usage.
Offers advice on clearing the lawn, adjusting cutting height, and proper mowing techniques.
Warns against operating on slopes exceeding 5 degrees due to rollover risk.
Provides instructions on how to safely turn off the engine.
Warns against leaving the ignition key in the machine to prevent unauthorized use.
Lists essential safety steps before performing maintenance or servicing.
Instructions for raising, removing, and reinstalling the engine hood.
Provides notes on periodic maintenance, warnings, and pre-use checks.
Instructions for draining and refilling engine oil, including locating the drain valve.
Tests for the operator presence system to ensure it functions correctly.
Tests for the Reverse Operation System (ROS) to ensure it functions correctly.
Emphasizes the importance of sharp blades and proper sharpening.
Provides essential tips for proper blade installation and care.
Details the 5-star blade and its bolt, including tightening direction.
Details the 6-star blade and its bolt, including tightening direction.
Emphasizes keeping blades sharp and replacing damaged ones.
Step-by-step instructions for removing the cutting unit from the tractor.
Instructions for reassembling the cutting unit after removal.
Details the process of replacing the drive belt for the cutting unit.
Instructions for adjusting the cutting unit for side-to-side levelness.
Instructions for adjusting the cutting unit for side-to-side levelness.
Guides on adjusting the motion control lever for proper neutral positioning.
Emphasizes keeping the fan and cooling fins clean for proper operation.
States that the transaxle is factory sealed and requires no fluid maintenance.
Lists common reasons why the engine fails to start.
Troubleshooting steps for when the starter motor does not turn the engine.
Identifies causes for uneven engine operation.
Troubleshooting steps for a weak-feeling engine.
Lists common causes for engine overheating.
Troubleshooting steps for a battery that is not charging.
Troubleshooting steps for non-functional lighting.
Identifies causes for excessive vibration of the machine.
Lists common causes for uneven cutting results.
Outlines procedures for cleaning, oiling, and storing the tractor after the mowing season.
Warns against using gasoline for cleaning and recommends degreasing detergent and warm water.
Provides information for ordering spare parts and contacting service centers.
