EasyManua.ls Logo

Crary CWS CASE IH 2162 - User Manual

Crary CWS CASE IH 2162
92 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OWNER’S/PARTS
MANUAL
RECORD SERIAL NUMBER HERE
Manual P/N 50887-00
Rev. 110118.07
SN Range: G00001-Current
CASE IH
2162
MACDON
FD1
FD70
FD75
CRARY WIND SYSTEM

Table of Contents

Questions and Answers

  • J
    Joseph AriasAug 13, 2025
    What to do if gear box is leaking on Crary CWS CASE IH 2162?
    • J
      James SanchezAug 13, 2025
      If the gear box on your Crary Farm Equipment is leaking or overheating, first check the oil level and replace it if necessary. If the breather is plugged, remove, clean, and reinstall it. If the seals are leaking, install a new seal kit. If debris is pinched between the base and the screen, adjust the air base closer to the screen. Ensure the screen cleaner is adjusted to revolve close to the screen, but not touching it.
  • M
    matthewjonesAug 25, 2025
    How to prevent shattering of grain ahead of cutter bar on Crary CWS CASE IH 2162?
    • S
      sextonsaraAug 25, 2025
      To prevent grain shattering ahead of the cutter bar on your Crary Farm Equipment, ensure the reel speed is coordinated with the ground speed to avoid excessive agitation. If the reel is too low, raise it. Also, consider slowing down the ground speed if it's too fast for the crop conditions.
  • W
    walljamesNov 3, 2025
    What to do if cut crop is building up on Crary Farm Equipment?
    • J
      John JohnsonNov 3, 2025
      If you observe cut crop building up and falling from the front or behind the cutter bar, or grain heads are being lost at the cutter bar of your Crary Farm Equipment, take these steps: * Ensure the reel is set low enough to sweep material from the cutter bar. * Extend the rigid cutter bar if there's insufficient ledge for crop travel. * Adjust the outer ends of the auger to 1/2” (13mm) clearance of the platform bottom and check finger clearance. * Adjust the manifold to direct airflow at the cutter bar to keep it clean. Also, clean debris from the rotary screen, check for obstructions in the flex hose, manifold, or drop tubes, check the butterfly position to allow more airflow, verify the fan rpm, adjust the combine shaft speed, and check for the proper gearbox ratio for the comb...

Summary

System Information

How to Reach Us

Contact information for parts and service.

Disclaimer and Product Safety Statement

Legal notices, design change policy, and safety commitment.

Serial Number Location

Guidance on locating the machine's serial number.

Limited Warranty

Introduction

Safety Precautions

Safety Alert Symbols and Signal Words

Explains hazard symbols and signal words for critical warnings.

General and Operator Safety

Outlines operator responsibilities and general safety measures.

Specific Safety Procedures

Covers operating, maintenance, hydraulic, PTO, transport, and storage safety.

Safety Decals and Training Sign-Off

Importance of safety decals and record of training completion.

Assembly Procedures

Gearbox;Fan Mount Installation

Step-by-step mounting for gearbox and fan assemblies.

Driveline, Manifold, and Hose Routing

Installation of drive lines, manifolds, and flex hoses.

Reel Arm Mount Assembly

Instructions for assembling reel arm mounts for various header types.

Electrical Wiring Installation

Guidelines for installing the electrical wiring system components.

Operation and Adjustments

Machine Components and Controls Overview

Identification of key components and operation of controls.

Initial Adjustments and Break-In

Procedures for initial setup, torque limiter, and break-in.

Operating Hints, Transport, and Storage

Recommendations for operation, transport, and storage.

Service & Maintenance

Maintenance Schedule and Lubrication

Detailed checklist and lubrication guide for routine maintenance.

Gearbox and Driveline Servicing

Procedures for gearbox oil, seals, and driveline components.

Fan, Hose, and Slip Clutch Maintenance

Care and maintenance for fan housing, air hose, and slip clutch.

Troubleshooting Guide

Problem Diagnosis and Solutions

Lists common issues, their causes, and recommended solutions.

Technical Specifications

Bolt Torque Specifications

Table of recommended torque values for various bolt sizes and grades.

Parts Catalog

Gearbox and Fan Assembly Parts

Exploded views and part numbers for gearbox and fan components.

Driveline, Hose, and Manifold Parts

Parts lists and diagrams for driveline, hose, and manifold assemblies.

Reel Arm Mount Parts

Diagrams and part numbers for reel arm mount components.

Accessory and Kit Parts

Parts for optional kits like drop tubes, cleaners, and brushes.

Available Options

Crary CWS CASE IH 2162 Specifications

General IconGeneral
BrandCrary
ModelCWS CASE IH 2162
CategoryFarm Equipment
LanguageEnglish

Related product manuals