Crary Air Reel - User Manual

Questions and Answers

T
Thomas DavidAug 19, 2025
How to fix crop not feeding auger in Crary Air Reel?
- C
  Crystal Chandler DDSAug 19, 2025
  If the crop isn't feeding into the auger, here's what you can do: * Gradually move the reel back. * Adjust the tine angle one notch at a time closer to perpendicular. * Gradually adjust the airflow closer to the auger until the crop is feeding properly. * Gradually adjust the air volume to achieve optimum crop flow with a minimum amount of air. * Gradually increase the auger speed. * Gradually increase the header speed.
B
Bryan CampbellAug 21, 2025
How to stop wrapping on the reel of Crary Air Reel?
- B
  brewerkellyAug 21, 2025
  To address wrapping on the reel, consider the following adjustments: * Gradually raise the reel to reduce or eliminate wrapping while maintaining crop flow. * Gradually move the reel forward to reduce or eliminate wrapping while maintaining crop flow. * Gradually reduce the reel speed. * Adjust the tine angle one notch at a time closer to perpendicular.
J
Jason HermanAug 23, 2025
How to prevent build-up of crop in the corners of Crary Air Reel?
- M
  mistyhammondAug 23, 2025
  To prevent crop build-up in the corners, consider these adjustments: * Gradually adjust crop dividers to direct crop towards the center. * Gradually direct air from adjustable nozzles to move crop from the area. * Add auxiliary tines.
C
carterchristopherAug 26, 2025
What to do if crop is not feeding auger in Crary Cables and connectors?
- A
  Andrew HornAug 26, 2025
  If the crop is not feeding into the auger, take these steps: 1. Move the reel back gradually. 2. Adjust the tine angle one notch at a time, making it closer to perpendicular. 3. Adjust the airflow closer to the auger gradually, until the crop feeds properly. 4. Adjust the air volume gradually to achieve optimum crop flow with a minimum amount of air. 5. Increase the auger speed gradually. 6. Increase the header speed gradually.
P
patrick09Aug 28, 2025
What to do if there is buildup of crop on the sickle of Crary Cables and connectors?
- D
  debrareedAug 28, 2025
  If you notice a buildup of crop on the sickle, you should: 1. Gradually adjust the airflow to the middle of the sickle. 2. Gradually increase the air volume until proper crop flow is restored.
R
rwilliamsAug 30, 2025
What to do if there is down or lodged crop with Crary Cables and connectors?
- N
  Nicholas GibsonAug 30, 2025
  If you're dealing with down or lodged crop, here's what you can do: 1. Move the reel ahead gradually to achieve the best feeding. 2. Increase the reel speed gradually to achieve the best feeding. 3. Adjust the airflow forward gradually to assist the reel in lifting the crop. 4. Increase the air volume gradually as needed. 5. Adjust the tine angle back one tooth at a time to achieve the best feeding.
G
Gary RobinsonSep 1, 2025
How to stop wrapping on the reel of Crary Cables and connectors?
- J
  Johnny ToddSep 1, 2025
  To reduce or eliminate wrapping on the reel, consider these steps: 1. Raise the reel gradually while maintaining crop flow. 2. Move the reel forward gradually while maintaining crop flow. 3. Reduce the reel speed gradually. 4. Adjust the tine angle one notch at a time, making it closer to perpendicular.
A
Amanda WashingtonSep 3, 2025
How to prevent shatter loss with Crary Cables and connectors?
- M
  mark40Sep 3, 2025
  To address shatter loss, consider the following adjustments: 1. Decrease the reel speed gradually. 2. Increase the airflow gradually.
H
Heather GrahamSep 5, 2025
How to prevent flying debris from Crary Cables and connectors?
- J
  jeffery62Sep 5, 2025
  To prevent flying debris, gradually reduce the airflow while ensuring you maintain adequate crop flow.
L
Lisa FoleySep 7, 2025
How to prevent crop buildup in the corners of Crary Cables and connectors?
- C
  Cory WhiteSep 7, 2025
  To prevent crop buildup in the corners: 1. Gradually adjust the crop dividers to direct the crop towards the center. 2. Gradually direct air from adjustable nozzles to move the crop from the area. 3. Add auxiliary tines.