Need help?Do you have a question about the Crate Professional BV-60H and is the answer not in the manual?
Output Specifications| output power rating | 50 watts RMS @ 5% THD 8 or 16 ohm load, 120 VAC |
|---|
Gain and Tone Control| gain channel 1 | 66dB, tones at “10” @ 1kHz |
|---|---|
| gain channel 2 | 101dB, tones @ “10” @ 1kHz |
| tone control range channel 1 low | 16dB @ 100Hz |
| tone control range channel 1 mid | 20dB @ 300Hz |
| tone control range channel 1 high | 10dB @ 10kHz |
| tone control range channel 2 low | 15dB @ 100Hz |
| tone control range channel 2 mid | 13dB @ 500Hz |
| tone control range channel 2 high | 10dB @ 10kHz |
| presence | 5dB @ 10kHz |
Electrical Specifications| input impedance | 1M ohm |
|---|---|
| maximum signal accepted | 2.8V peak to peak |
| line out level | 1.2V RMS nominal |
Tube Types| preamp tube type | 12AX7A (3) |
|---|---|
| power amp tube type | 12AX7A (1), 6L6GT/5881 (2) |
Power Requirements| power requirements | 115V 60Hz, 110VA |
|---|---|
| fuse | 2.5A Slo-Blo Fuse |
Weight and Dimensions| size | 12”H x 30.25”W x 10”D |
|---|---|
| weight | 50lbs |
Output Specifications| output power rating | 100 watts RMS @ 5% THD 8 or 16 ohm load, 120 VAC |
|---|
Gain and Tone Control| gain channel 1 | 66dB, tones at “10” @ 1kHz |
|---|---|
| gain channel 2 | 101dB, tones @ “10” @ 1kHz |
| tone control range channel 1 low | 16dB @ 100Hz |
| tone control range channel 1 mid | 20dB @ 300Hz |
| tone control range channel 1 high | 10dB @ 10kHz |
| tone control range channel 2 low | 15dB @ 100Hz |
| tone control range channel 2 mid | 13dB @ 500Hz |
| tone control range channel 2 high | 10dB @ 10kHz |
| presence | 5dB @ 10kHz |
Electrical Specifications| input impedance | 1M ohm |
|---|---|
| maximum signal accepted | 2.8V peak to peak |
| line out level | 1.2V RMS nominal |
Tube Types| preamp tube type | 12AX7A (3) |
|---|---|
| power amp tube type | 12AX7A (1), 6L6GT/5881 (4) |
Power Requirements| power requirements | 115V 60Hz, 180VA |
|---|---|
| fuse | 5A Slo-Blo Fuse |
Weight and Dimensions| size | 12”H x 30.25”W x 10”D |
|---|---|
| weight | 50lbs |
Key safety warnings, precautions, and noise exposure guidelines.
All-tube design, dual channels with independent controls.
Presence control, effects loop, and footswitch integration.
Line out, impedance selection, and USA manufacturing.
Controls for power, standby, reverb levels, and presence.
Controls for effects loop and channel selection.
EQ, gain, master volume, and input controls for both channels.
Fuse socket and AC line input.
Footswitch, effects loop, and line out jacks.
Speaker output jacks and impedance selector.
Recommended settings for clean and edge-of-breakup tones.
Settings for rhythm playing and warm, full clean tones.
Recommended settings for high-gain distortion and heavy tones.
To Next Page
