Crestron TSW-1050 User Manual

quickstart guide
TSW-1050
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TSW-1050
10.1” Touch Screen
The Crestron
®
TSW-1050 touch screen installs into a standard 2-gang or 3-gang U.S electrical box or a
2-gang European electrical box. It can also be attached directly to drywall and other surfaces over the
front of a 2 3/8” (60 mm) high by 3 3/8” (86 mm) wide cutout. When installed, it protrudes just 1/2”
(13 mm) from the mounting surface and magnetically adheres to its included mounting bracket.
It is supplied with screws for installation.
1
Install the Touch Screen
QUICKSTART DOC. 7468D (2035664, Sheet 1 of 2) 10.13
1
To mount the TSW-1050 into an electrical box, use the following procedure:
1. Use four of the eight included screws (four #06-32 x 3/4” or four 3 x 16 mm) to attach the mounting
bracket (2034503) to the electrical box, as shown in the following illustrations.
For U.S.-style installations, use the #06-32 x 3/4” screws (2033247).
For European-style installations, use the 3 x 16 mm screws (2013788).
Mount the TSW-1050 into a U.S. Electrical Box
2. Power and data connection to the TSW-1050 is provided by a single Ethernet cable connected to
the LAN port at the rear of the unit. A Crestron PoE power supply or PoE-capable network switch is
recommended. Apply power after the Ethernet cable is connected.
3. Carefully position the touch screen over the mounting bracket and gently place it in position.
The magnets on the rear of the touch screen hold it in place on the mounting bracket.
Hardware Connections for the TSW-1050
Mount the TSW-1050 into a European Electrical Box
For Regulatory Compliance information, refer to the latest
version of Doc. 7469.
NOTE: For U.S.-style installations, use a #2 Phillips screwdriver. For European-style installations,
use a #1 Phillips screwdriver or equivalent.
Mounting Bracket
(2034503)
Screws (4) #06-32 x 3/4”
(2033247)
TSW-1050
U.S. Electrical Box
Mounting Bracket
(2034503)
Screws (4) 3 x 16 mm
(2013788)
TSW-1050
European Electrical Box
Reset Button
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN

Crestron TSW-1050 Specifications

General

Resolution	1280 x 800 pixels
Touch Technology	Capacitive
Connectivity	Ethernet, Wi-Fi, Bluetooth
Power over Ethernet	Yes
Microphone	Yes
Speakers	Yes
Weight	2.2 lbs
Display Size	10.1 inches
Wi-Fi	802.11 a/b/g/n
Processor	Quad Core
Memory	2 GB RAM
Storage	8 GB Flash
Mounting	Wall or table

Summary

Install the Touch Screen

Mounting Bracket Installation

Attaching the mounting bracket to the electrical box using specified screws for U.S. or European installations.

Ethernet Connection for Power and Data

Connecting the TSW-1050 via a single Ethernet cable with PoE for power and data.

Magnetic Mounting

Positioning the touch screen onto the mounting bracket where magnets hold it in place.

Establish Communication

TCP/IP Communication Method

Using Crestron Toolbox for TCP/IP communication with the TSW-1050.

Device Discovery Tool

Configure the Touch Screen

Initial Setup Screen

The screen displayed upon initial power-up, allowing basic configuration.

Accessing Setup Functions

Pinout Reference

LAN PoE Port Pinout

Recommended Cleaning

Cleaning Procedures