7
8
Important safety instructions
PLEASE READ THIS ENTIRE DOCUMENT PRIOR TO
SETTING UP, OPERATING, AND SERVICING YOUR
CRICUT
®
SMART CUTTING MACHINE. PLEASE
FOLLOW THE ENCLOSED INSTRUCTIONS, ONLINE
INSTRUCTIONS, AND OTHER OFFICIAL CRICUT
INSTRUCTIONAL MATERIALS.
In these instructions the term “Machine” means
Cricut Venture™.
WARNING: Risk of Injury, Fire, and
Electric Shock.
Operating Machine in a manner not
prescribed in the enclosed instructions, online
instructions, and other official Cricut materials may
result in damage to the Machine, property damage,
injury, or even death.
Machine is intended to be operated by an
adult only. Not intended for use by children
12 years or under. Always supervise
children around Machine.
Use Machine only for its intended crafting purpose.
INDOOR USE ONLY. MACHINE IS INTENDED
FOR INDOOR USE IN DRY LOCATIONS ONLY.
DO NOT USE IN OR NEAR WATER. DO NOT IMMERSE
IN WATER OR ANY OTHER LIQUID.
Machine is not intended for use by persons with
reduced physical, sensory or cognitive capabilities,
or lack of experience and knowledge, unless they are
supervised by a person responsible for their safety
and familiar with the safe operation of Machine.
Disconnect the electrical power when not in use by
unplugging cord from outlet.
Disconnect the electrical power by unplugging cord
from the outlet before servicing or cleaning.
Do not expose Machine to temperatures above 38°C
(100°F ).
Only clean Machine with a soft cloth dampened
with glass cleaner or water. Never use any kind
of flammable liquid to clean Machine. Do not use
solvents such as acetone or nail polish remover to
clean Machine as these will permanently damage
Machine’s surfaces.
CAUTION: Cutoff tool contains sharp blade.
Use with extreme care. If cutoff tool is broken,
worn down, or blade is showing, please
carefully discard immediately and replace with a
new manual cutoff tool (sold separately).
Always unplug Machine before replacing the cutting
blade. Blades are extremely sharp and should be
handled with caution and extreme care. Prevent
blade contact with hands and body to avoid injury.
Do not allow children to handle blades. Blades and
other small parts are choking hazards and should
be kept and stored away from children.
Do not open, modify, or otherwise tamper
with Machine.
Do not operate if Machine or cord is damaged.
Contact Cricut Member Care for service: cricut.
com/contact or USA and Canada: 1-877-727-4288/
Mexico: 0800-266-0135.
Use only Cricut approved power adapters.
Always turn Machine OFF before unplugging
from the electrical outlet. Never pull on the cord
to disconnect Machine from the electrical outlet;
instead, grasp the plug and pull to disconnect
Machine.
CAUTION: To provide continued protection
against risk of electric shock, connect to
properly grounded outlets only.
The power cord should be positioned so that it
will not drape over the countertop or tabletop
where it can be tripped over, snagged, or pulled on
unintentionally (especially by children).
CAUTION: To minimize the possibility of the
machine falling and causing potential
personal injury and/or damage to the machine,
always use Machine on a sturdy, non-slick surface.
Do not place or use Machine on tableclothed
surface or on any other surface prone to slippage.
Always ensure that no debris or excess dust is
present underneath Machine, including on
Machine’s rubber feet.
Machine should be placed near the edge of the
table or other sturdy surface on which it is placed on,
so as to properly allow Machine’s Mat Supports Arms
to fully extend unimpeded.
Do not operate Machine close to blinds, curtains,
window coverings, or other materials that may get
caught or tangled in the Machine.
Do not touch the mat or material during cutting
even if the mat or material stops moving. Do not
touch the mat or material until Machine ejects the
mat or material from Machine.
CAUTION: Make sure your work space has
enough space in the front and back of
Machine to allow the cutting mat to move through
the Machine freely.
Do not place your fingers or other objects in
Machine while connected to electrical power, or
while Machine is powered on, or during cutting
operations.
Keep hair, jewelry, loose clothing, fingers, other body
parts, and any other items that could get caught
in the moving parts away from Machine while it is
operating as the rapid movements of the cutting
carriage, mat, and material during operation may
cause injury.
Machine should never be left or stored outside,
in unheated or unairconditioned spaces, or in
environments where Machine can come in contact
with water.
Product specifications
Model CXPL401C
Size (Width x Length x Height) 34.82 in x 10.40 in x 8.81 in (884.5 mm x 264.1 mm x 223.8 mm)
Weight 33.9 lbs (15.4 kg)
Power input (appliance inlet) Input: 100-240 V ~, 50/60 Hz, 2 A
EN
Morpheus_User_Guide_Intl_v15.indd 7-8Morpheus_User_Guide_Intl_v15.indd 7-8 4/11/23 7:52 PM4/11/23 7:52 PM
To Next Page
Loading...
