To Next PageTo Next Page
Need help?Do you have a question about the Crossfire BMF1000D and is the answer not in the manual?
Detailed technical specifications for BMF1000D and BMF600D models.
Crossover settings including low pass and subsonic filter ranges.
Explains how the single-channel amplifiers operate and their speaker output configuration.
Illustrates load configurations for 4 ohm subwoofers connected to amplifier outputs.
Proper placement and clearance for optimal heat dissipation and amplifier longevity.
Recommendations for pre-drilling mounting holes to prevent damage during installation.
Visual comparison of incorrect vs. correct mounting for effective heat management.
Procedure for checking vehicle battery voltage before connecting the amplifier.
Specifies fuse values and wire gauge for different amplifier models up to 20ft.
Guidelines for safely routing and connecting the power cable to the battery.
Requirements for ground wire gauge and color to ensure proper connection.
Steps for selecting and securing a solid ground point for the amplifier.
Guidance on locating the +12V switched source from the head unit or vehicle.
Instructions for connecting the remote turn-on wire to the amplifier and source unit.
Specifies minimum 12 gauge speaker wire for Class 'D' amplifiers and connection tips.
Instructions for stripping and connecting speaker wires to the amplifier terminals and loudspeakers.
Guidance on routing wires, creating slits, and leaving adequate slack for mounting.
Procedure for stripping wire insulation and connecting to amplifier terminals securely.
Emphasizes using proper signal cables for clear signal transmission to the amplifier.
Notes on RCA cable differences, shielding, and twisted pair for noise rejection.
Tips for routing RCA cables away from noise sources like engine noise and fans.
Explains the 'LOW IN' RCA receptacles and correct cable balancing (red/right, black/left).
Details on Lowpass Crossover, Subsonic Filter, Preamp Output, and Digital Remote Level Control.
Explains the variable lowpass filter from 50Hz to 250Hz for subwoofer blending.
Clarifies that the crossover is always active due to the amplifier's limited frequency range.
Reduces low-frequency harmonics and noise damaging to subwoofers and amplifiers.
Variable 20Hz-50Hz, selectable ON/OFF, and optimal frequency recommendations.
Allows driver-side adjustment of amplifier output level; connects directly to amplifier.
Provides a buffered signal for linking amplifiers without RCA y-cables.
Includes switchable crossover (HPF, LPF, Full) from 50Hz to 250Hz for system flexibility.
Explains bridging two amplifiers for double output, requiring 2ohm minimum impedance.
Details the three Master/Slave settings (0, 180, Slave) and their application.
Visual guide for connecting two amplifiers in a bridged configuration for increased output.
Instructions on setting preamp controls and master/slave configuration for bridged amps.
Three-step process to match amplifier input level to source unit output without distortion.
Clarifies that gain control is not a volume knob and warns against improper use.
Specifies that only the 'Master' amplifier's gain control is adjustable when bridging.
Explanation of the Green (power ON) and Red (protection mode) LED indicators.
Wiring diagram for a two-way system using HPF and FULL crossover settings.
Wiring diagram for a multi-subwoofer setup using FULL crossover settings for each.
Detailed technical specifications for BMF1000D and BMF600D models.
Crossover settings including low pass and subsonic filter ranges.
Explains how the single-channel amplifiers operate and their speaker output configuration.
Illustrates load configurations for 4 ohm subwoofers connected to amplifier outputs.
Proper placement and clearance for optimal heat dissipation and amplifier longevity.
Recommendations for pre-drilling mounting holes to prevent damage during installation.
Visual comparison of incorrect vs. correct mounting for effective heat management.
Procedure for checking vehicle battery voltage before connecting the amplifier.
Specifies fuse values and wire gauge for different amplifier models up to 20ft.
Guidelines for safely routing and connecting the power cable to the battery.
Requirements for ground wire gauge and color to ensure proper connection.
Steps for selecting and securing a solid ground point for the amplifier.
Guidance on locating the +12V switched source from the head unit or vehicle.
Instructions for connecting the remote turn-on wire to the amplifier and source unit.
Specifies minimum 12 gauge speaker wire for Class 'D' amplifiers and connection tips.
Instructions for stripping and connecting speaker wires to the amplifier terminals and loudspeakers.
Guidance on routing wires, creating slits, and leaving adequate slack for mounting.
Procedure for stripping wire insulation and connecting to amplifier terminals securely.
Emphasizes using proper signal cables for clear signal transmission to the amplifier.
Notes on RCA cable differences, shielding, and twisted pair for noise rejection.
Tips for routing RCA cables away from noise sources like engine noise and fans.
Explains the 'LOW IN' RCA receptacles and correct cable balancing (red/right, black/left).
Details on Lowpass Crossover, Subsonic Filter, Preamp Output, and Digital Remote Level Control.
Explains the variable lowpass filter from 50Hz to 250Hz for subwoofer blending.
Clarifies that the crossover is always active due to the amplifier's limited frequency range.
Reduces low-frequency harmonics and noise damaging to subwoofers and amplifiers.
Variable 20Hz-50Hz, selectable ON/OFF, and optimal frequency recommendations.
Allows driver-side adjustment of amplifier output level; connects directly to amplifier.
Provides a buffered signal for linking amplifiers without RCA y-cables.
Includes switchable crossover (HPF, LPF, Full) from 50Hz to 250Hz for system flexibility.
Explains bridging two amplifiers for double output, requiring 2ohm minimum impedance.
Details the three Master/Slave settings (0, 180, Slave) and their application.
Visual guide for connecting two amplifiers in a bridged configuration for increased output.
Instructions on setting preamp controls and master/slave configuration for bridged amps.
Three-step process to match amplifier input level to source unit output without distortion.
Clarifies that gain control is not a volume knob and warns against improper use.
Specifies that only the 'Master' amplifier's gain control is adjustable when bridging.
Explanation of the Green (power ON) and Red (protection mode) LED indicators.
Wiring diagram for a two-way system using HPF and FULL crossover settings.
Wiring diagram for a multi-subwoofer setup using FULL crossover settings for each.
General| Brand | Crossfire |
|---|---|
| Model | BMF1000D |
| Category | Car Amplifier |
| Language | English |
