To Next PageTo Next Page
Need help?Do you have a question about the Crown 2/300 and is the answer not in the manual?
General| Channels | 2 |
|---|---|
| 8 Ohm Bridged Mono Power | 900W |
| 4 Ohm Stereo Power | 450W |
| Input Impedance | 20kΩ balanced, 10kΩ unbalanced |
| Dimensions | 19" |
| Weight | 25 lb |
| 8 Ohm Stereo Power | 300W per channel |
Key features and technologies of the CDi DriveCore Series amplifiers.
Guidance on navigating and utilizing the operation manual effectively.
Procedures for unpacking the amplifier and checking for transit damage.
Lists required installation materials and guidelines for adequate amplifier cooling.
Detailed explanation of the front panel's controls, indicators, and display elements.
Description of all rear panel connectors for audio, network, and control interfaces.
Steps for connecting AC power and performing the initial amplifier power-up sequence.
Essential safety guidelines and precautions for amplifier operation and setup.
Instructions for connecting audio sources to the amplifier inputs.
Guidelines for connecting loudspeakers to the amplifier outputs.
Visual representation of the amplifier's front panel menu hierarchy.
Methods for adjusting system-wide and individual channel volume levels.
Explanation of the default home screen display and available navigation options.
Step-by-step guide for initial amplifier configuration using the front panel wizard.
Steps for assigning input sources and configuring output channels.
How to configure input wiring and bridge mono operation for output pairs.
Process for selecting and assigning audio sources to amplifier inputs.
Configuration options for BLU link digital audio transport, including sample rate and priority.
Setting output impedance modes (Low Z, 70V, 100V) for different speaker configurations.
Manual adjustment of digital signal processing modules like delay, EQ, and crossover.
Configuring input and output delay times for driver alignment and system timing.
Editing crossover filter types, frequencies, and slopes for speaker frequency management.
Adjusting input and output equalization using parametric EQ bands.
Configuring peak, RMS, and thermal limiters to protect drivers and the amplifier.
Overview of using Audio Architect software for amplifier configuration and control.
Steps for configuring amplifier network settings via front panel or software.
Utilizing NetSetter for discovering and configuring HiQnet devices on the network.
Understanding the differences between offline and online operation in Audio Architect.
Associating discovered hardware devices with their virtual representations in Audio Architect.
Exploring the functions and controls of the main amplifier control panel in Audio Architect.
Accessing and configuring amplifier details like firmware, temperature, and panel lockout.
Assigning input sources and configuring output routing within Audio Architect.
Setting BLU link clock parameters and routing audio signals to BLU link outputs.
Configuring amp wiring, bridge mode, and output impedance via Audio Architect.
Adjusting crossover filters and input/output equalization settings using Audio Architect.
Configuring delay times and LevelMAX limiter settings within Audio Architect.
Using the signal generator for tuning, troubleshooting, and testing loudspeakers.
Backing up and loading amplifier presets and device configurations.
Wiring and setup example for dual-mode operation with low impedance speakers.
Wiring and setup example for bridge-mono operation with low impedance speakers.
Wiring and setup example for dual-mode operation with high impedance speakers.
Wiring and setup example for bridge-mono operation with high impedance speakers.
Details on BLU link digital audio bus capabilities, channel count, and latency.
Instructions for physically connecting BLU link devices in a network loop.
Interpreting the LED indicators on BLU link ports for status and connectivity.
Understanding BLU link bus mastership negotiation and fault tolerance mechanisms.
Viewing current BLU link sample rate, priority, and connection status.
Procedures for saving amplifier configurations as user presets from the front panel.
Steps for recalling saved device presets onto the amplifier.
Configuring front panel LCD sleep timers and data light behavior.
Enabling front panel lockout to prevent unauthorized access and tampering.
Accessing diagnostic information such as firmware, voltage, and temperature readings.
Setting the amplifier's input sensitivity and gain mode.
Detailed pinout and functional description of the GPIO control port.
Using the AUX port for remote standby (sleep) and amplifier status monitoring.
Listing and explaining amplifier fault conditions and their causes.
Information on thermal protection limits and auto-insertion of high-pass filters.
Details on AC voltage protection and fan cooling behavior under fault conditions.
Resolving problems related to the power indicator and front panel display.
Troubleshooting amplifier not turning on or responding to the power button.
Diagnosing and resolving thermal faults and general fault error messages.
Identifying and fixing problems related to distorted sound, no sound, or no input signal.
Table detailing output power for different models and impedance loads.
Table showing input sensitivity values for various gain modes and models.
Overview of the warranty period, coverage, and items excluded from warranty.
Instructions on how to contact Crown for warranty service and obtain authorization.
Procedures for obtaining service through authorized centers or factory repair.
Guidelines for packing and shipping products for factory service.
List of open source libraries used and their associated licenses and copyright information.
