Need help?Do you have a question about the CRT MICRON U/V and is the answer not in the manual?
General| Brand | CRT |
|---|---|
| Model | MICRON U/V |
| Category | Transceiver |
| Language | English |
Lists standard accessories included with the transceiver, such as microphone and cables.
Lists optional accessories available for purchase, like PC cables and antennas.
Provides instructions for installing the transceiver securely inside a vehicle.
Explains how to connect the DC power cable to the transceiver and power source.
Details the procedure for replacing blown fuses, including type and rating specifications.
Guides users on selecting and connecting an efficient antenna for optimal performance.
Explains how to connect an external speaker, including impedance and plug type.
Identifies and explains the functions of the controls and indicators on the front panel.
Details the connectors and ports located on the rear panel of the transceiver.
Explains the various icons and information displayed on the transceiver's LCD screen.
Describes the keys and functions of the microphone, including a connector diagram.
Explains how to set the radio to operate in Amateur Transceiver or Channel Transceiver mode.
Details the different modes within Amateur Transceiver operation: Frequency+Channel, Channel+Name Tag, and VFO.
Describes the Channel Transceiver mode where the LCD displays channel name or number.
Instructions on how to turn the transceiver on and off, including display messages.
How to adjust the speaker volume using the control knob or mute function.
Methods for adjusting frequency using the channel knob or microphone keypad.
Procedures for changing channels using the channel knob or direct number input.
Explains how the transceiver indicates incoming calls and signal strength.
Details how to transmit, including microphone usage and conditions.
How to switch between main and sub channels for dual watch functionality.
Procedures for switching between VFO (frequency) and Channel modes.
Steps to edit existing channels, including frequency, CTCSS/DCS, and storage.
Instructions on how to delete unwanted channels from memory.
Configuring CTCSS or DCS codes for encoding and decoding signals.
Explains how to perform a CTCSS scan to find matching signaling tones.
Details the process of performing a DCS scan to find matching digital codes.
How to initiate frequency or channel scans to monitor signals.
Procedures for adding or deleting channels from the scan list.
How to disable or temporarily disable the squelch for monitoring weak signals.
Instructions on how to lock and unlock the keypad to prevent accidental operation.
Settings for enabling or disabling audible beep tones and adjusting their level.
How to configure the frequency step size for tuning and scanning.
Options to change the LCD display mode, such as frequency or channel name.
Adjusting the squelch sensitivity to filter out background noise.
Adjusting the audio output volume level to one of 36 available settings.
Enabling or disabling a password to turn on the transceiver.
Configuring how long the transceiver pauses on a signal during a scan.
Setting the duration for pausing scans when a signal is detected.
Enabling or disabling the automatic power-on function when connected to power.
Configuring the dual watch feature to monitor two channels simultaneously.
Adjusting the brightness level of the LCD display backlight.
Setting a limit for continuous transmission time to prevent overheating.
Configuring the automatic power-off timer based on preset durations.
Setting pilot frequencies used to activate repeaters.
Adjusting the display orientation of the LCD screen (normal or reversed).
Configuring whether to use the main speaker, microphone speaker, or both.
Enabling or disabling the RTDF function for separate RX/TX frequencies.
Restoring the transceiver settings and channels to their factory defaults.
Configuring CTCSS or DCS decode settings for receiving signals.
Setting up CTCSS or DCS encode for transmitting signals.
Selecting the transmission power level: High, Medium, or Low.
Setting up signaling combinations for improved blocking of irrelevant signals.
Choosing the appropriate bandwidth (Wide, Middle, Narrow) for local conditions.
Enabling the frequency reverse function to swap TX and RX frequencies.
Enabling or disabling the talk around function for direct communication.
Setting transmit frequency offset and direction relative to receive frequency.
Naming or renaming channels for easier identification on the display.
Configuring busy channel lockout to prevent transmitting on occupied channels.
Disabling or enabling transmission (TX) mode for the transceiver.
Customizing the functions of the main unit's keypad keys.
Configuring the backlight settings for the microphone keypad.
Adjusting the brightness of the microphone keypad backlight.
Customizing specific keys on the H-PA H-PD microphone keypad.
Steps to install the necessary USB driver for connecting the transceiver to a computer.
Lists the default factory settings for various parameters after a reset.
Provides potential causes and solutions for common operational problems.
General technical specifications of the transceiver, including frequency range and dimensions.
Detailed technical specifications for the transceiver's performance, like power output and sensitivity.
To Next Page
