Cub Cadet CC3600 - User Manual

Questions and Answers

N
Nicole NewtonAug 9, 2025
What causes low pressure in my Cub Cadet Pressure Washer after normal use?
- R
  Robert WebbAug 9, 2025
  If your Cub Cadet Pressure Washer has no or low pressure after a period of normal use: * **Seals/packing:** The seal or packing may be worn. Consult an authorized service dealer. * **Valves:** The valves may be worn or obstructed. Consult an authorized service dealer. * **Unloader piston:** The unloader piston may be worn. Consult an authorized service dealer.
E
Edwin MorganAug 13, 2025
Why is my Cub Cadet Pressure Washer leaking water at the pump?
- R
  rmillerAug 13, 2025
  If water is leaking at the pump of your Cub Cadet Pressure Washer: * **Connections:** Tighten any loose connections. * **Piston packings:** The piston packings may be worn. Consult an authorized service dealer. * **O-ring:** The o-ring may be worn or torn. Consult an authorized service dealer. * **Pump head/tubes:** The pump head or tubes may be damaged from freezing. Consult an authorized service dealer.
J
Jennifer SheltonAug 18, 2025
Why does my Cub Cadet Pressure Washer pump pulsate?
- M
  Mario MartinAug 18, 2025
  If the pump of your Cub Cadet Pressure Washer pulsates, the nozzle may be obstructed. Refer to the “Nozzle Cleaning” paragraph for the correct procedure.
R
Rhonda StevensAug 22, 2025
Why won't my Cub Cadet Pressure Washer engine start?
- A
  Ashley DanielAug 22, 2025
  If your Cub Cadet Pressure Washer engine won't start, there are several potential causes: * **No fuel:** Add fresh fuel. Consult the engine manual for guidance. * **Pressure build-up:** Squeeze the gun trigger to relieve pressure. * **Choke lever position:** Move the choke to the "Choke" position initially. Refer to the engine manual. * **Spark plug wire:** Ensure the spark plug wire is securely attached. See the engine manual.
E
Erika ThompsonAug 27, 2025
What to do if my Cub Cadet Pressure Washer will not draw chemicals?
- T
  Theresa LewisAug 27, 2025
  If your Cub Cadet Pressure Washer isn't drawing chemicals, check these possible causes: * **Spray wand setting:** Ensure the spray wand is set to low pressure. Refer to the “Use Spray Wand” paragraph. * **Chemical filter:** Clean the chemical filter. * **Siphon hose:** Make sure the end of the detergent siphon hose is fully submerged in the cleaning solution. * **Chemical thickness:** Dilute the chemical if it's too thick, aiming for a water-like consistency. * **Pressure hose:** Lengthen the water supply hose instead of the high-pressure hose. * **Chemical injector:** If there is chemical build up in the chemical injector, consult an authorized service dealer.
K
kwilliamsAug 31, 2025
Why is my Cub Cadet Pressure Washer leaking water at the gun/spray wand connection?
- M
  Malik WongAug 31, 2025
  If water is leaking at the gun/spray wand connection of your Cub Cadet Pressure Washer: * **O-ring:** Check the o-ring for wear or tears and replace it if necessary. * **Hose connection:** Tighten the hose connection.
C
Casey LeeNov 4, 2025
Why is my Cub Cadet Pressure Washer leaking oil at the pump?
- M
  Mary SweeneyNov 4, 2025
  If you notice oil leaking at the pump of your Cub Cadet Pressure Washer, consider the following: * **Oil seals:** The oil seals may be worn. Consult an authorized service dealer. * **Drain plug:** Tighten the drain plug if it is loose. Check and replace the drain plug o-ring if worn. * **Fill plug:** Check and replace the fill plug o-ring if worn. * **Oil level:** Ensure the pump is not overfilled and contains the correct amount of oil. * **Oil type:** Use the correct type of oil. If the wrong oil was used, drain and refill with the correct type. * **Vent plug:** Clean the vent plug by blowing air through it. If the problem persists, replace the plug. Refer to the engine manual. * **Air filter:** Clean and/or replace the air filter element if it is filled with oil. Refer to ...