What causes low pressure in my Cub Cadet Pressure Washer after normal use?
If your Cub Cadet Pressure Washer has no or low pressure after a period of normal use: * **Seals/packing:** The seal or packing may be worn. Consult an authorized service dealer. * **Valves:** The valves may be worn or obstructed. Consult an authorized service dealer. * **Unloader piston:** The unloader piston may be worn. Consult an authorized service dealer.
Why is my Cub Cadet Pressure Washer leaking water at the pump?
If water is leaking at the pump of your Cub Cadet Pressure Washer: * **Connections:** Tighten any loose connections. * **Piston packings:** The piston packings may be worn. Consult an authorized service dealer. * **O-ring:** The o-ring may be worn or torn. Consult an authorized service dealer. * **Pump head/tubes:** The pump head or tubes may be damaged from freezing. Consult an authorized service dealer.
Why does my Cub Cadet Pressure Washer pump pulsate?
If the pump of your Cub Cadet Pressure Washer pulsates, the nozzle may be obstructed. Refer to the “Nozzle Cleaning” paragraph for the correct procedure.
Why won't my Cub Cadet Pressure Washer engine start?
If your Cub Cadet Pressure Washer engine won't start, there are several potential causes: * **No fuel:** Add fresh fuel. Consult the engine manual for guidance. * **Pressure build-up:** Squeeze the gun trigger to relieve pressure. * **Choke lever position:** Move the choke to the "Choke" position initially. Refer to the engine manual. * **Spark plug wire:** Ensure the spark plug wire is securely attached. See the engine manual.
What to do if my Cub Cadet Pressure Washer will not draw chemicals?
If your Cub Cadet Pressure Washer isn't drawing chemicals, check these possible causes: * **Spray wand setting:** Ensure the spray wand is set to low pressure. Refer to the “Use Spray Wand” paragraph. * **Chemical filter:** Clean the chemical filter. * **Siphon hose:** Make sure the end of the detergent siphon hose is fully submerged in the cleaning solution. * **Chemical thickness:** Dilute the chemical if it's too thick, aiming for a water-like consistency. * **Pressure hose:** Lengthen the water supply hose instead of the high-pressure hose. * **Chemical injector:** If there is chemical build up in the chemical injector, consult an authorized service dealer.
Why is my Cub Cadet Pressure Washer leaking water at the gun/spray wand connection?
If water is leaking at the gun/spray wand connection of your Cub Cadet Pressure Washer: * **O-ring:** Check the o-ring for wear or tears and replace it if necessary. * **Hose connection:** Tighten the hose connection.
Why is my Cub Cadet Pressure Washer leaking oil at the pump?
If you notice oil leaking at the pump of your Cub Cadet Pressure Washer, consider the following: * **Oil seals:** The oil seals may be worn. Consult an authorized service dealer. * **Drain plug:** Tighten the drain plug if it is loose. Check and replace the drain plug o-ring if worn. * **Fill plug:** Check and replace the fill plug o-ring if worn. * **Oil level:** Ensure the pump is not overfilled and contains the correct amount of oil. * **Oil type:** Use the correct type of oil. If the wrong oil was used, drain and refill with the correct type. * **Vent plug:** Clean the vent plug by blowing air through it. If the problem persists, replace the plug. Refer to the engine manual. * **Air filter:** Clean and/or replace the air filter element if it is filled with oil. Refer to ...
Explains hazard classifications and general safety symbols for user protection.
Details risks of fire, explosion, and dangers from carbon monoxide exhaust.
Covers dangers of fluid injection, spray projectiles, and general unsafe operation.
Addresses safety for transport, storage, electrical, chemical, lifting, tire, and hot surface hazards.
Addresses issues like engine not starting and low or no water pressure.
General| Power Source | Gasoline |
|---|---|
| Max Pressure | 3300 PSI |
| Flow Rate | 2.5 GPM |
| Hose Length | 25 ft |
| Pump Type | Axial Cam |
To Next Page
