Why does my Cuenod C160 GX507/8 burner stop and nothing happens?
If your Cuenod Indoor Fireplace burner stops and nothing happens, it could be due to several reasons: insufficient gas pressure (adjust distribution pressure), a misadjusted or faulty gas pressure switch (check or replace it), a foreign body in the pressure take-off pipe (clean the pipes without pressurized fluid), or misadjusted/faulty thermostats (adjust or replace them).
What to do if my Cuenod Indoor Fireplace unit shows [ [ [ + \ \ [ [ [ [ + \?
If your Cuenod Indoor Fireplace unit displays '[ [ [ + \ \ [ [ [ [ + \', it could be due to the air pressure switch. The contact may not close (check the pressure take-off for any foreign bodies and the wiring) or the contact opens during start-up or operation (adjust or change the pressure switch).
Why Cuenod Indoor Fireplace burner doesn't start after thermostatic closure?
If your Cuenod Indoor Fireplace burner doesn't start after thermostatic closure and the unit doesn't signal any fault, it may be due to a low or missing power supply (check the source of low or missing voltage) or a faulty unit (change the unit).
What does it mean if my Cuenod C160 GX507/8 Indoor Fireplace unit shows [ [ + \ \ \?
If your Cuenod Indoor Fireplace unit displays '[ [ + \ \ \', it could be due to a spurious light during the surveillance phase (change the valve) or, in the event of a cell burner, a faulty cell (change the cell).
What does it mean when my Cuenod Indoor Fireplace unit displays \ \ + [ [ [?
If your Cuenod Indoor Fireplace unit displays '\ \ + [ [ [', it indicates that the air pressure switch contact is welded. You should change or adjust the pressure switch.
What to do if Cuenod Indoor Fireplace burner starts briefly then stops and shows [ [ 9 \ \ \ - \ \ \ \?
If the burner of your Cuenod Indoor Fireplace starts briefly when powered up, then stops and shows the signal '[ [ 9 \ \ \ - \ \ \ \', it means the unit has been purposely shut down. Reset the unit.
What to do if Cuenod C160 GX507/8 Indoor Fireplace unit is on [ + \ \ \ \?
If your Cuenod Indoor Fireplace unit is showing '[ + \ \ \ \' and not working, it might be due to several reasons: * No flame signal at the end of safety time or an unsuitable gas flow rate: Adjust the gas flow rate. * Faulty flame monitoring circuit: Check the state and position of the ionization probe in relation to mass. * No ignition arc: Check the state and connections of the ionization circuit (cable and measuring bridge). * Ignition electrode(s) short-circuiting: Adjust, clean, or replace the electrodes. * Damaged or faulty ignition cables: Connect or replace the cables. * Faulty ignition transformer: Replace the ignition transformer. * Control unit issue: Replace the transformer or change the control unit. * Electromagnetic valves not opening: Check the wiring betw...
Instructions and regulations for installation and start-up, manufacturer liability.
Essential pre-start checks, including voltage, polarity, and leakage testing.
Description and settings of the MBVEF gas valve, including its components and pressure adjustments.
Details on the VGD gas valve and SKP75 regulator, their function and preset values.
Working principle, installation, and testing of the leakage controller VPS 504 S02.
Characteristics and operation diagram of the SG 513 control and safety unit.
Detailed procedures for burner working cycle test, firing, and safety unit checks.
Troubleshooting guide for burner stopping issues, including gas pressure and thermostat faults.
Interpreting unit status signals (light signals) and identifying causes for faults.
General| Model | C160 GX507/8 |
|---|---|
| Category | Indoor Fireplace |
| Fuel Type | Gas |
| Efficiency | 85% |
| Ignition Type | Electronic |
| Thermostat | Yes |
| Remote Control | Yes |
| Flame Effect | Realistic |
To Next Page
