Cuenod C210 GX507/8 - User Manual

Questions and Answers

T
Taylor HendersonAug 5, 2025
Why does my Cuenod Indoor Fireplace burner stop and nothing happens?
- E
  Elizabeth JonesAug 5, 2025
  If your Cuenod Indoor Fireplace burner stops and nothing happens, it could be due to several reasons: insufficient gas pressure (adjust distribution pressure), a misadjusted or faulty gas pressure switch (check or replace it), a foreign body in the pressure take-off pipe (clean the pipes without pressurized fluid), or misadjusted/faulty thermostats (adjust or replace them).
C
Chad FlynnAug 14, 2025
What to do if my Cuenod C210 GX507/8 unit shows [ [ [ + \ \ [ [ [ [ + \?
- A
  amyscottAug 14, 2025
  If your Cuenod Indoor Fireplace unit displays '[ [ [ + \ \ [ [ [ [ + \', it could be due to the air pressure switch. The contact may not close (check the pressure take-off for any foreign bodies and the wiring) or the contact opens during start-up or operation (adjust or change the pressure switch).
B
babbottAug 18, 2025
Why Cuenod C210 GX507/8 Indoor Fireplace burner doesn't start after thermostatic closure?
- S
  salazarkentAug 18, 2025
  If your Cuenod Indoor Fireplace burner doesn't start after thermostatic closure and the unit doesn't signal any fault, it may be due to a low or missing power supply (check the source of low or missing voltage) or a faulty unit (change the unit).
J
jameslunaAug 22, 2025
What does it mean if my Cuenod C210 GX507/8 unit shows [ [ + \ \ \?
- N
  Norman BurgessAug 23, 2025
  If your Cuenod Indoor Fireplace unit displays '[ [ + \ \ \', it could be due to a spurious light during the surveillance phase (change the valve) or, in the event of a cell burner, a faulty cell (change the cell).
L
Lisa WilsonAug 27, 2025
What does it mean when my Cuenod C210 GX507/8 Indoor Fireplace unit displays \ \ + [ [ [?
- M
  matthew14Aug 27, 2025
  If your Cuenod Indoor Fireplace unit displays '\ \ + [ [ [', it indicates that the air pressure switch contact is welded. You should change or adjust the pressure switch.
V
Victor MckeeAug 31, 2025
What to do if Cuenod Indoor Fireplace burner starts briefly then stops and shows [ [ 9 \ \ \ - \ \ \ \?
- B
  Brian CollinsAug 31, 2025
  If the burner of your Cuenod Indoor Fireplace starts briefly when powered up, then stops and shows the signal '[ [ 9 \ \ \ - \ \ \ \', it means the unit has been purposely shut down. Reset the unit.
H
Heidi SellersNov 9, 2025
What to do if Cuenod C210 GX507/8 Indoor Fireplace unit is on [ + \ \ \ \?
- A
  Alyssa ValentineNov 9, 2025
  If your Cuenod Indoor Fireplace unit is showing '[ + \ \ \ \' and not working, it might be due to several reasons: * No flame signal at the end of safety time or an unsuitable gas flow rate: Adjust the gas flow rate. * Faulty flame monitoring circuit: Check the state and position of the ionization probe in relation to mass. * No ignition arc: Check the state and connections of the ionization circuit (cable and measuring bridge). * Ignition electrode(s) short-circuiting: Adjust, clean, or replace the electrodes. * Damaged or faulty ignition cables: Connect or replace the cables. * Faulty ignition transformer: Replace the ignition transformer. * Control unit issue: Replace the transformer or change the control unit. * Electromagnetic valves not opening: Check the wiring betw...