EasyManua.ls Logo

Culligan Sulfur-Cleer - User Manual

Culligan Sulfur-Cleer
27 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Culligan
®
Sulfur-Cleer
Automatic
Water Filter
Owners Guide

Questions and Answers

  • T
    tina52Aug 16, 2025
    What to do if Culligan Water Filtration System is continuously running to drain?
    • K
      Kristin BriggsAug 16, 2025
      If your Culligan Water Filtration System is continuously running to drain, first ensure continuous electrical service is available by checking the plug, breaker, and fuse. If the issue persists, the circuit board may be faulty and require replacement. For other potential causes, such as a faulty drive motor or foreign material lodged in the piston, it's recommended to call your Culligan dealer for service.
  • J
    Jose SosaAug 18, 2025
    Why is my Culligan Water Filtration System spurting air from filtered water fixtures?
    • J
      Julia MannAug 19, 2025
      Air spurting from filtered water fixtures in your Culligan system can occur if the service flow demand exceeds the water supply available from your well pump system; in this case repair or replace well pump system. It can also happen if water flow is restricted by supply piping or water treatment equipment, for this call your Culligan dealer for service.
  • J
    James RichardsonAug 21, 2025
    How to resolve loss of media through drain line in Culligan Water Filtration System?
    • C
      Christian FuentesAug 21, 2025
      Loss of media through the drain line in your Culligan system can occur for several reasons. New filter media is shipped in a dry condition and must soak for 24 hours to become fully saturated before a backwash cycle, so clean drain line flow control, control valve body, seals, spacers and piston assemblies. Excess air accumulated in media tank from aeration pump or in filter system from water supply or well pump can also cause this issue, so repair well pump system or call your Culligan dealer for service. If the cause was due to temporary loss of water main pressure; the problem will most likely correct itself with the return of continuous pressure.
  • W
    William LawrenceAug 25, 2025
    Why is my Culligan Water Filtration System spurting air at outside water fixtures?
    • M
      murraykristyAug 26, 2025
      Air spurting at outside or non-filtered water fixtures in your Culligan system can be due to improper installation location, foreign material preventing the check valve, or a worn or faulty check valve. For these issues, it's best to call your Culligan dealer for service.
  • D
    Debra HessAug 27, 2025
    How to reduce excessive noise during Culligan Water Filtration System regeneration?
    • J
      Jared FloresAug 28, 2025
      Excessive noise during regeneration of your Culligan system can be caused by an inadequate drain line size or the drain line vibrating against other objects. For these issues, it's recommended to call your Culligan dealer for service.
  • A
    Aaron RoblesAug 30, 2025
    Why is the water from my Culligan Water Filtration System effervescent?
    • G
      Gloria JamesAug 30, 2025
      If the water from your Culligan system is effervescent, it's likely due to the water supply being naturally aerated under well system pressure. As the water is released to the atmosphere, air molecules separate from the water molecules. This natural phenomenon will typically dissipate in seconds. If preferred, water can be drawn and stored in an open container prior to use; for example, fill a pitcher and store it in the refrigerator for cool, fresh drinking water.
  • S
    Savannah RichardsSep 2, 2025
    What to do if Culligan Water Filtration System is leaking from the relief valve?
    • T
      tayloroliviaSep 2, 2025
      If your Culligan Water Filtration System is leaking from the relief valve, it indicates the pressure has exceeded the valve's rating and caused it to open. In this case, call your Culligan dealer for service.
  • J
    James WilsonSep 5, 2025
    What causes blue green staining from Culligan Water Filtration System?
    • J
      Jason MontoyaSep 5, 2025
      Blue-green staining from your Culligan system is often caused by a low pH condition in the raw water supply. In rare cases, highly aerated water combined with a specific water supply can create a slightly corrosive condition. For these issues, it's recommended to call your Culligan dealer for service.
  • A
    Aaron DunnSep 9, 2025
    What to do if Culligan Water Filtration System compressor doesn’t run?
    • P
      Pamela BowersSep 9, 2025
      If the compressor on your Culligan system isn’t running, first ensure it's plugged in. If it is, the relay settings might be incorrect, or the relay could be bad. For relay issues, it's recommended to call your Culligan dealer for service.
  • G
    gonzalesmichaelSep 12, 2025
    Why does my Culligan Water Filtration System compressor run continuously?
    • R
      Robert ConleySep 12, 2025
      If the compressor on your Culligan system runs continuously, it could be due to incorrect relay settings or a bad relay. For these issues, it's recommended to call your Culligan dealer for service.

Summary

Operating Conditions

Alkalinity

Specifies the minimum alkalinity required for efficient iron and hydrogen sulfide removal.

Hydrogen Sulfide

Details the system's effectiveness for hydrogen sulfide reduction based on concentration.

Iron

States the maximum rating for ferrous (clear water) iron removal.

Familiarization

Programming

Statistic Functions

When and How to Bypass Your Water Conditioner

Regeneration with Bleach

Caution! USE AND HANDLING OF HOUSEHOLD BLEACH

Provides safety warnings and handling instructions for bleach used in regeneration.

Things to Check Before You Call for Service

No Water

Provides steps to troubleshoot lack of water flow, including checking the bypass.

Preventative Maintenance

Troubleshooting Guide

Iron bleed-through or staining

Lists causes and solutions for iron-related water issues.

Fails to regenerate

Provides troubleshooting steps for when the unit does not regenerate.

Water contaminant levels are greater than limits

Addresses issues where contaminant levels exceed established limits.

Inadequate aeration

Lists causes and solutions for insufficient air in the system.

Exceeding recommended filter system flow rate

Discusses problems related to exceeding the system's flow rate.

Regeneration during service flow demand

Addresses issues of regeneration occurring during active water usage.

Raw water bleeding through filter

Lists causes and solutions for raw water passing through the filter.

Water leaking from relief valve

Provides causes and solutions for leaks from the relief valve.

Air spurting at outside or non-filtered water fixtures

Lists causes and solutions for air spurting from unfiltered water outlets.

Air spurting from filtered water fixtures

Addresses causes and solutions for air spurting from filtered water outlets.

Loss of media through drain line

Details causes and solutions for filter media being lost through the drain.

Excessive noise during regeneration

Lists causes and solutions for unusual noises during regeneration.

Water is running to drain continuously

Lists causes and solutions for continuous water flow to the drain.

Compressor doesnt run

Provides troubleshooting steps for a non-operational compressor.

Compressor run with excessive noise

Lists causes and solutions for noisy compressor operation.

Compressor runs continuously

Addresses causes and solutions for the compressor running non-stop.

Performance Data Sheet

Culligan Limited Warranty

Culligan Sulfur-Cleer Specifications

General IconGeneral
BrandCulligan
ModelSulfur-Cleer
CategoryWater Filtration Systems
LanguageEnglish

Related product manuals