CYmodel Ju87 stuka - User Manual

SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
lAssemble this kit only in places out of childrens reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Wing Span: 2540mm (100in)
2
Wing Area: 94.5dm (1463.5sq.in)
Total Length: 2000 mm (78.7 in)
Engine :80cc gas engine
Radio : 5-6 channels ,10 servos
Ju87 stukaJu87 stuka
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8018

Summary

Safety Precautions

General Safety Advice

Key safety guidelines for builders regarding assembly, operation, and potential hazards of the model.

Required Equipment for Operation

Radio System, Servos, and Engine Components

Details on the necessary radio transmitter, servos, engine, muffler, and propeller for the model.

Consumables and Other Supplies

List of glues, silicone tubes, and other operational consumables.

Tools Required for Assembly

Essential Hand Tools

List of necessary tools like knives, screwdrivers, pliers, and cutters.

Installation: Flap and Aileron

Install the Flap

Step-by-step guide for attaching the flap component to the aircraft wing.

Install the Aileron

Step-by-step guide for attaching the aileron component to the aircraft wing.

Installation: Main Landing Gear

Install the Main Landing Gear

Procedure for installing the main landing gear assembly onto the aircraft.

Installation: Servos and Wing

Install the Servo

Procedure for installing a servo into the designated location.

Main Wing Assembly

Steps for assembling and preparing the main wing sections.

Landing Gear Installation

Install the Main Landing Gear (Steps 3 & 4)

Further steps for installing the main landing gear assembly.

Installation: Control Surfaces

Install the Elevator

Procedure for attaching the elevator control surface.

Install the Rudder

Procedure for attaching the rudder control surface.

Installation: Tail Wheel and Servos

Install the Tail Wheel

Procedure for installing the tail wheel assembly.

Install the Rudder Servo

Procedure for installing the servo controlling the rudder.

Installation: Control Linkages and Engine

Install the Rod for Elevator

Procedure for installing the control rod for the elevator.

Install the Elevator Servo

Procedure for installing the servo controlling the elevator.

Install the Throttle Servo

Procedure for installing the servo controlling the throttle.

Installing the Engine (80 cc)

Steps for mounting the 80cc engine onto the aircraft.

Assembly: Fuel Tank and Radio

Assembly of the Full Tank

Procedure for assembling and installing the fuel tank system.

Radio Equipment Installation

Steps for installing the battery, ignition, and receiver.

Installation: Cowling and Canopy

Install the Thr Cowling

Procedure for attaching the engine cowling.

Install the Canopy

Steps for cutting and fitting the canopy.

Control Surface Adjustments

Aileron and Flap Adjustment

Adjusting travel for ailerons and flaps for optimal flight.

Elevator Adjustment

Adjusting travel for the elevator control surface.

Rudder Adjustment

Adjusting travel for the rudder control surface.

Center of Gravity (CG) Adjustment

Final CG Check and Adjustment

Ensuring correct center of gravity by repositioning receiver and battery.

CYmodel Ju87 stuka Specifications

General

Brand	CYmodel
Model	Ju87 stuka
Category	Toy
Language	English