DAB ACTIVE DRIVER PLUS T/T 5.5 User Manual

ISTRUZIONI PER L'INSTALLAZIONE E LA MANUTENZIONE
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
INSTRUCTIONS POUR L'INSTALLATION ET LA MAINTENANCE
INSTALLATIONS- UND WARTUNGSANLEITUNGEN
INSTRUCTIES VOOR INSTALLATIE EN ONDERHOUD
INSTRUCCIONES DE INSTALACIÓN Y MANTENIMIENTO
INSTALLATIONS- OCH UNDERHÅLLSANVISNING
ΟΔΗΓΙΕΣ ΓΙΑ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ ΚΑΙ ΤΗ ΣΥΝΤΗΡΗΣΗ
KURMA VE BAKIM BİLGİLERİ
NÁVOD NA INŠTALÁCIU A ÚDRŽBU
РУКОВОДСТВО ПО МОНТАЖУ И ТЕХНИЧЕСКОМУ ОБСЛУЖИВАНИЮ
INSTRUCTIUNI PENTRU INSTALARE SI INTRETINERE
INSTRUÇÕES PARA A INSTALAÇÃO E A MANUTENÇÃO
ASENNUS- JA HUOLTO-OHJEET
INSTRUKCJA MONTAŻU I KONSERWACJI
ІНСТРУКЦІЇ ЗІ ВСТАНОВЛЕННЯ ТА ТЕХНІЧНОГО ОБСЛУГОВУВАННЯ
NÁVOD K INSTALACI A ÚDRŽBĚ
    
ACTIVE DRIVER PLUS M/T 1.0
ACTIVE DRIVER PLUS M/T 2.2
ACTIVE DRIVER PLUS T/T 3
ACTIVE DRIVER PLUS T/T 5.5
ACTIVE DRIVER PLUS M/M 1.1
ACTIVE DRIVER PLUS M/M 1.8 / DV
ACTIVE DRIVER PLUS M/M 1.5 / DV

DAB ACTIVE DRIVER PLUS T/T 5.5 Specifications

General

Brand	DAB
Model	ACTIVE DRIVER PLUS T/T 5.5
Category	Inverter
Language	English

Summary

KEY

WARNINGS

Important safety warnings and symbols used in the manual.

1 GENERAL INFORMATION

1.2 Technical specifications

Details the technical data and limitations for different inverter models.

2 INSTALLATION

2.1 Hydraulic connection

Procedures for connecting the inverter to the hydraulic system, including single and multi-pump setups.

2.2 Electrical connections

Guidance on making electrical connections for pumps and power supply.

2.3 CONNECTION TO THE POWER SUPPLY LINE

Details on connecting the inverter to the main power supply line.

2.4 Configuration of the Integrated Inverter

Steps for configuring the built-in inverter settings.

2.6 Operation

Explanation of the normal operating modes and functions of the inverter.

3 KEYBOARD AND DISPLAY

3.4 Parameter setting block via Password

How to secure and access parameter settings using a password.

4 MULTI INVERTER SYSTEM

4.2 Setting up a multi inverter system

Steps and requirements for configuring a multi-inverter setup.

4.3 Multi inverter operating parameters

Classification and description of parameters relevant to multi-inverter operation.

4.4 Initial start-up of multiple inverter system

Guide for the first power-up and configuration of a multi-inverter system.

4.5 Multi-inverter settings

Details on configuring specific settings for multi-inverter operation.

5 POWER-UP AND START-UP

5.1 Initial power-up operations

Steps to follow upon initial system power-up.

5.2 Wizard

5.3 Troubleshooting on initial installation

Common issues encountered during initial installation and their solutions.

6 KEY TO INDIVIDUAL PARAMETERS

6.3 Setpoint menu

6.5 Installer menu

6.6 Technical Assistance Menu

6.6.1 TB: Water failure block time

6.6.2 T1: Shutdown time after low pressure signal

6.6.3 T2: Shutdown delay

6.6.4 GP: Proportional gain coefficient

6.6.5 GI: Integral gain coefficient

6.6.6 FS: Maximum rotation frequency

6.6.7 FL: Minimum rotation frequency

6.6.8 Setting the number of inverters and reserves

7 PROTECTION SYSTEMS

7.1 Protection systems

7.1.1 Anti-Freeze (Protection against freezing of water in the system)

7.2 Description of blocks

7.2.1 "BL" Block due to water failure

7.3 Manual reset of error conditions

7.4 Auto-reset of error conditions

8 RESET AND FACTORY SETTINGS

8.3 Restoring the factory settings

9 FIRMWARE UPDATE

9.2 Update

Detailed procedure for updating the firmware across connected inverters.