Daikin AGZ130E - User Manual

112 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Installation, Operation,

and Maintenance Manual

Trailblazer

™

Air-Cooled Scroll Chillers

Model AGZ, E Vintage

30 to 240 Tons (100 to 840 kW)

HFC-410A Refrigerant

50/60 Hz

IOM 1206-7

Group: Chiller

Part Number: IOM1206-7

Date: July 2016

Table of Contents

Questions and Answers

J
Jenna SloanAug 14, 2025
What causes motor overload relays or circuit breakers to open in my Daikin Chiller?
- S
  Scott BonillaAug 15, 2025
  If motor overload relays or circuit breakers are opening in your Daikin Chiller, it could be due to a voltage imbalance or voltage being out of range, requiring correction of the power supply. Defective or grounded wiring in the motor can also cause this, necessitating compressor replacement. Loose power wiring or burnt contactors are other potential causes; check all connections and tighten them, replacing contactors if needed. High condenser temperature can also trigger this issue; refer to corrective steps for High Discharge Pressure.
G
gibsonjacobAug 21, 2025
Why is my Daikin AGZ130E's compressor noisy or vibrating?
- A
  Angela WatkinsAug 21, 2025
  A noisy or vibrating Daikin Chiller compressor can stem from several issues. It could be due to low lift or an inverted start, which may require control adjustments or condenser fan VFDs. Another cause might be the compressor running in reverse; check the unit and compressor for correct phasing. Improper piping or support on the suction or discharge lines can also lead to noise and vibration, necessitating relocation, addition, or removal of hangers. Worn compressor isolator bushings can be a source of the problem, requiring replacement. In more severe cases, the compressor may have a mechanical failure, which would also require replacement.
A
alanvaughnAug 25, 2025
What causes high discharge pressure in my Daikin Chiller?
- L
  Lawrence EatonAug 25, 2025
  High discharge pressure in your Daikin Chiller can result from several factors. Noncondensables in the system may be the cause; extract them using approved procedures or replace the charge. The circuit might be overcharged with refrigerant, requiring you to remove the excess and check liquid subcooling. Ensure the optional discharge shutoff valve is open. Incorrect condenser fan control wiring or a non-running fan can also lead to high pressure; correct the wiring or check the electrical circuit and fan motor, respectively. A dirty condenser coil or air recirculation could also be responsible; clean the coil or correct the recirculation issue.
T
Tiffany HarrisAug 31, 2025
What to do if my Daikin AGZ130E compressor will not stage up?
- B
  Barry BrennanAug 31, 2025
  If your Daikin Chiller compressor isn't staging up, it could be due to a defective capacity control, which would need replacement. Another possibility is a faulty sensor or wiring, also requiring replacement. Finally, the stages might not be set correctly for the application; adjust the controller settings accordingly.
J
James EvansSep 3, 2025
Why are the compressor staging intervals too short on my Daikin AGZ130E Chiller?
- R
  Ronald HoffmanSep 3, 2025
  Short compressor staging intervals on your Daikin Chiller can be attributed to several factors. The control band may not be set properly, necessitating an adjustment of the controller settings for the application. A faulty water temperature sensor could be the cause, requiring replacement. Insufficient water flow can also lead to this issue; correct the flow. Other potential causes include rapid temperature or flow swings (stabilize the load), oversized equipment (evaluate equipment selection), the chiller being enabled with no load (evaluate BAS sequence and settings), or light loads (evaluate the need for HGBP or thermal inertia).
L
Lori OlsonSep 10, 2025
What causes the compressor thermal protection switch to open on my Daikin Chiller?
- J
  Justin WeaverSep 10, 2025
  The compressor thermal protection switch opening on your Daikin Chiller can be caused by several factors. It could be due to operating beyond design conditions, requiring correction to stay within allowable limits. A discharge valve not being open can also trigger this; ensure the valve is open. Short cycling can lead to this issue; stabilize the load or correct control settings for the application. Voltage range issues or imbalance can be responsible; check and correct the voltage. High superheat can also cause the switch to open; adjust to correct superheat. In some cases, compressor mechanical failure may be the cause, necessitating compressor replacement.
M
Matthew PerkinsNov 17, 2025
What to do if my Daikin Chiller compressor will not run?
- S
  smithkevinNov 17, 2025
  If your Daikin Chiller compressor isn't running, there are several potential causes. First, ensure that the main or compressor disconnect switch is closed. Check for blown fuses or open circuit breakers, examining electrical circuits and motor windings for shorts or grounds. Also, check for loose or corroded connections, replacing fuses or resetting breakers after correcting any faults. Thermal overloads may have tripped; these are auto-resetting, so check voltages, cycle times, and mechanical operations, allowing time for the reset. A defective contactor or coil could also be the issue, requiring replacement. The system might be shut down by equipment protection devices; determine the cause and correct it before restarting. The unit may not require cooling, so wait until it calls for it. ...
J
Judith WilsonNov 26, 2025
How to fix low suction pressure in a Daikin AGZ130E?
- S
  Savannah CoxNov 27, 2025
  Low suction pressure in a Daikin Chiller can arise from various causes. Rapid load swings might be the culprit, requiring load stabilization. A lack of refrigerant could be the issue; check for leaks, repair them, and add refrigerant, also check the liquid sight glass. A fouled liquid line filter drier can cause this; check the pressure drop across it and replace if needed. An expansion valve malfunction may also be responsible; repair or replace it and adjust for proper superheat. Low condensing temperature can contribute; check the means for regulating condenser temperature. Other potential causes include compressors not staging properly (see corrective steps - Compressor Staging Intervals Too Low), insufficient water flow (correct the flow), excess or wrong oil used (recover or change t...

Summary

Installation and Application Information

Operating and Standby Limits

Defines the acceptable temperature and fluid limits for unit operation.

Unit Placement and Clearances

Guidelines for selecting unit location and maintaining necessary service clearances.

Chilled Water Piping

Specifies requirements for field-installed water piping, strainers, and flow switches.

Water Flow Limitations

Explains constant and variable evaporator flow and their limitations.

Evaporator Freeze Protection

Details methods to protect the evaporator from freezing.

High and Low Ambient Operation

Describes operational capabilities and requirements for high and low ambient temperatures.

Electrical Data

Unit Controller Operation

Controller Inputs;Outputs

Detailed listing of controller analog and digital inputs and outputs.

Set Points and Configuration

Configuration of unit and circuit level set points and dynamic ranges.

Security and Passwords

Procedures for accessing and editing unit parameters securely.

Sequence of Operation

Cool Mode Sequence

Step-by-step operational logic for cooling mode.

Ice Mode Sequence

Step-by-step operational logic for ice mode.

Circuit Sequence of Operation

Operational logic for individual refrigerant circuits.

Unit Functions

Evaporator Flow and Freeze Protection

Covers evaporator flow, freeze protection, pump selection, and LWT target.

Unit Capacity Control and Staging

Manages compressor staging, capacity overrides, and demand limits.

RapidRestore Option

Enables faster startup and loading after power interruptions.

Sound Reduction

Feature to reduce sound levels by limiting condenser fan speeds.

Circuit Functions

EXV Control and Superheat Target

Details EXV control states, superheat targets, and position commands.

Capacity Overrides

Conditions that override automatic capacity control for safe operation.

Alarms

Unit Fault Alarms

Details on alarms related to power, flow, freeze protection, and sensors.

Compressor Module Communication Alarms

Alarms indicating communication failure with compressor modules.

Unit Problem Alarms

Alarms related to pump failures and communication issues.

Unit Warning Alarms

Warnings for external events, demand limit, and LWT reset inputs.

Circuit Fault Alarms

Faults related to low/high pressure, sensors, and pumpdown.

Using the Controller

Passwords and Edit Mode

Optional Low Ambient Fan VFD

VFD Functionality

Faults and Errors

Startup and Shutdown Procedures

Pre Startup Checks

Startup Procedure

Shutdown Procedures

Component Operation

Compressor Communications and Status

Unit Maintenance

Condenser Coil Cleaning

Periodic Rinsing and Cleaning

System Adjustment

R-410 A Refrigerant Safety

Refrigerant Charging

Troubleshooting Chart

Compressor Issues

Compressor Staging and Oil Issues

Warranty Registration Form

Pre Startup Procedures and Checklist

Microtech Status Check

Microtech Setpoints and Alarms

Limited Product Warranty

Mandatory Startup and Registration

Sole Remedy and Liability

Daikin AGZ130E Specifications

General

Brand	Daikin
Model	AGZ130E
Category	Chiller
Language	English

Related product manuals

Daikin Trailblazer AGZ110-130E

Preview: Daikin AGZ 025D

Daikin AGZ 025D