How to troubleshoot Daikin Air Conditioner when the unit doesn't turn on?
If your Daikin Air Conditioner isn't powering on, check if the power cable is properly connected to the power supply terminal. Also, inspect the transformer's wire connection. If the transformer fuse has melted, it is recommended to consult a DAIKIN service center.
What to do if my Daikin Air Conditioner pump and compressor are running but oil cannot be cooled?
If your Daikin Air Conditioner's pump and compressor are running, but the oil isn't cooling, here are a few things to check: * Ensure there are no obstructions near the air intake or exhaust port. * Clean the air filter. * Verify that the temperature setting is appropriate. If the exhaust air temperature is almost the same as the room temperature while the compressor is running, the refrigerant gas may be low and needs refilling. Also, if the room temperature is high, compare the unit's capacity in the operating temperature range against the catalog to see if you need a model with higher capacity.
Why does my Daikin Air Conditioner show a high pressure error?
A high pressure error on your Daikin Air Conditioner can occur if the oil or room temperature is too high. Ensure you are using the unit within its specified operating range. Also, make sure there are no obstructions blocking the air intake or exhaust port, maintaining a clear space of at least 500 mm. A clogged air filter can also cause this issue, so clean it. If none of these solve the problem, contact the DAIKIN Contact Center.
What to do if oil does not flow in Daikin AKZ9 Air Conditioner, although the pump is running?
If oil isn't flowing in your Daikin Air Conditioner despite the pump running, and the pump sound level is high, check the following: 1. Ensure the pump suction pipe connection is tight. Check the pipe packing and retighten it securely. 2. Clean the suction strainer. If the oil in the oil tank is dirty, replace it. 3. Refill oil into the oil tank if the oil level is low. 4. If there's a large pressure loss in the oil discharge pipe, increase the oil pipe diameter and shorten the pipe length.
What causes a compressor high temperature error in my Daikin AKZ9?
A compressor high temperature error in your Daikin Air Conditioner can be caused by a few factors. First, check if the oil or room temperature is higher than the specified operating range and adjust accordingly. Ensure that there are no obstructions near the air intake or exhaust port that could impede ventilation. Lastly, a dirty air filter or condenser can also lead to this error, so make sure to clean them.
What to do if Daikin AKZ9 Air Conditioner compressor does not run, although the pump is running?
If your Daikin Air Conditioner's compressor isn't running even though the pump is, it could be due to several reasons: * The compressor restart prevention timer may be active. Check if the compressor starts after the timer's preset time has elapsed. * The low oil temperature protection device might be activated. Ensure the inlet oil temperature is 5°C or higher for normal operation. * The low ambient temperature protection device could be activated. Make sure the room temperature is 0°C or higher. * The capacity setting might be at 0% (Mode 9). Change the operation mode to a suitable setting.
What causes the pump over-current relay to activate on my Daikin Air Conditioner?
If the pump over-current relay is activated on your Daikin Air Conditioner, it could be due to several reasons: * The pump might be overloaded with high-viscosity oil. Use an operating fluid that provides 1.4 to 200 mm2/s viscosity within the specified oil temperature range. * The power supply voltage may be too low, causing the pump current to increase. Check if the voltage is within the specified operating range and look for any instantaneous voltage drops when peripheral equipment starts up. * There may be a break in the pump motor wiring (open-phase), or a foreign object caught in the pump, or a fault in the pump motor. In these cases, replace the pump motor.
How to fix DC fan motor lock error on Daikin AKZ9?
To address a DC fan motor lock error on your Daikin Air Conditioner, check the following: * Inspect the signal and engine wires between the filter board and the inverter board for any breaks or loose connections, as a drop in DC voltage can cause insufficient fan motor speed. * Examine the connector insertion and wires for breaks, as a fan motor-control board communication error may be the cause. If necessary, replace the control board. * If the DC fan motor is faulty, replace it.
Why can't I set the operation on my Daikin AKZ9 Air Conditioner?
If you're unable to set the operation on your Daikin Air Conditioner, here are a couple of things to check: * If you see “---” on the data display, the temperature sensor for the selected operation mode may not be connected. Ensure the corresponding temperature sensor is properly connected. * If “---” briefly appears when you press the [ENT] key, the protect switch might be ON. Turn OFF the protect switch (SW1) on the control board.
What to do if Daikin Air Conditioner pump does not run?
If the pump on your Daikin Air Conditioner isn't running, check the following: * Ensure the remote control input ([10]–[11]) is ON by checking the connection of the remote control input. * Verify that the unit isn't set to the operation lock mode. If it is, cancel the Lock mode on the control panel.
Safety measures for the installation process.
Procedures and precautions for moving and storing the unit.
Guidelines for selecting an appropriate installation location and oil piping.
Guidance on choosing appropriate pipe sizes and lengths.
Instructions and diagrams for connecting electrical wiring.
Detailed steps for electrical wiring, including circuit breaker installation.
Explains how to identify the specific model of the unit.
Verifies operating environment, installation, oil piping, applicable oil, and electrical wiring.
How to switch between different operating modes.
Explains how to adjust operational parameters and settings.
Setting the unit to maintain a constant oil temperature.
Adjusting oil temperature based on ambient or machine temperature.
Operating the unit at a specified cooling capacity percentage.
Steps to select and view monitored items on the control panel.
Steps to set the timer for starting the unit.
Details of parameters for additional setting functions.
Setting parameters to define temperature warning conditions.
Illustrates how temperature range warnings are applied.
Explains auto-tuning for improving temperature control performance.
Steps involved in executing the auto-tuning mode.
How to configure alarms for user-installed protection devices.
Details on mounting and using machine temperature tuning thermistors.
Steps for installing machine tuning thermistors.
Details on mounting and using returned oil temperature thermistors.
Steps for installing returned oil temperature thermistors.
How to connect the unit to a main machine for data exchange.
Steps for mounting the communication option board.
Daily checks for oil level, leaks, and voltage.
Periodic checks for suction strainer, air filter, condenser, etc.
Precautions for storing the unit for extended periods.
Common issues and corrective actions when the unit operates abnormally without alarms.
Lists alarm codes, causes, and corrective actions.
Lists warning codes, causes, and corrective actions.
General| Brand | Daikin |
|---|---|
| Model | AKZ9 Series |
| Category | Air Conditioner |
| Language | English |
To Next Page
