To Next PageTo Next PageHow to change Daikin Altherma EDHQ011BB6V3 temperature display from Fahrenheit to Celsius?
If the temperature display on your Daikin Heat Pump remote controller is showing °F instead of °C, it's likely that the ib and jb buttons were accidentally pressed simultaneously. To revert back to °C, press and hold the ib and jb buttons together for 5 seconds. Repeat the same process to switch back to °F if desired. The default setting is °C.
What to do if the Daikin Heat Pump water pressure relief valve is leaking?
If the water pressure relief valve on your Daikin Heat Pump is leaking, it might be due to dirt blocking the valve outlet. To check, turn the red knob on the valve counter-clockwise. If you don't hear a clacking sound, it's recommended to contact your local dealer. If water continues to run out, first close both the water inlet and outlet shut-off valves, and then contact your local dealer.
Why does the water pressure relief valve keep opening on my Daikin Heat Pump?
If the water pressure relief valve on your Daikin Heat Pump opens, it could be due to incorrect field wiring causing a misdetection of the tank type when setting the DIP switch SS2-2. To resolve this, check all field wiring between the unit and the tank switch box. Then, follow this reset procedure: 1. Power off the unit and set SS-2 to OFF. 2. Power on the unit. This will cause the unit to detect no domestic hot water tank. 3. Power off the unit again and set SS2-2 to ON. 4. Power on the unit. The unit will now redetect the tank type: either with a built-in electrical booster heater (EKHW*) or without (EKHTS).
What does 'nnnn' mean on my Daikin Altherma EDHQ011BB6V3 user interface?
If your Daikin Heat Pump user interface displays "nnnn" when pressing certain buttons, it indicates that the current permission level is restricting the use of that button. To resolve this, you need to change the "user permission level" field setting [0-00]. See section "10.10. Field settings" on page 32 for instructions.
General| Category | Heat Pump |
|---|---|
| Model | EDHQ011BB6V3 |
| Type | Air-to-Water Heat Pump |
| Heating Capacity | 11 kW |
| Energy Efficiency Class (Heating) | A+++ |
| Refrigerant | R-32 |
| Operating Temperature Range (Heating) | -20°C to 35°C |
| Power Supply | 3-phase, 400 V, 50 Hz |
Explains the severity and probability of warning symbols used in the manual.
Defines key terms like installation manual, dealer, installer, applicable legislation, etc.
Thanks the user for purchasing and outlines unit applications, combinations, and remote controller.
Describes the two main unit versions: heating/cooling (EB) and heating only (ED).
Explains special equipment in EDL/EBL units for low ambient temperatures and high humidity.
Lists optional accessories like heater sheets and drain sockets for specific unit models.
Details the availability of optional domestic hot water tanks in different sizes and types.
Provides information on the optional solar kit for domestic hot water tanks.
Illustrates common installation scenarios and system configurations for the unit.
Lists the standard accessories included with the unit, like manuals and wiring diagrams.
Provides instructions on how to access different compartments of the unit for inspection.
Identifies and describes the key components within the hydraulic and switch box compartments.
Details criteria for choosing a suitable installation site, considering ventilation, noise, and space.
Specifies the required clearances around the unit for proper installation and servicing.
Covers crucial steps before installation, including inspection, handling, and accessory checks.
Highlights essential precautions during installation to prevent damage or hazards.
Covers the procedures and precautions for connecting the unit to the water circuit.
Lists essential safety warnings and guidelines for all electrical wiring activities.
Provides a comprehensive list of internal components and their abbreviations used in wiring diagrams.
Illustrates the required field wiring connections between various system components.
Covers guidelines for field wiring, including cable requirements and specific connection procedures.
Provides instructions for installing the digital controller, including wiring and mounting.
Explains the purpose and configuration of DIP switch SS2 for various unit settings.
Details how to configure the unit when a room thermostat is connected, including DIP switch settings.
Explains how to configure pump operation based on thermostat connection and dual set point settings.
Guides on configuring the unit for different types of domestic hot water tanks.
Provides precautions for gradual water heating during initial start-up in low temperatures.
Lists essential checks to perform before powering on the unit for the first time.
Describes the initial power-up sequence and user interface display during unit initialization.
Explains how to select the appropriate pump speed based on system water flow requirements.
Guides on identifying and resolving initial installation abnormalities and error codes.
Introduces the concept of field settings for configuring the unit to match installation environment.
Provides a comprehensive table listing all field settings, their default values, ranges, and units.
Lists essential final checks to be performed after installation and before unit operation.
Outlines checks related to electrical wiring and earthing before initiating the test run.
Describes the automatic test run procedure for cooling mode and potential issues.
Explains how to perform manual test runs for heating, cooling, and domestic water heating.
Details the function for automatically executing a screed drying program for underfloor heating.
Provides initial steps for troubleshooting, including visual inspections and safety checks.
Lists common symptoms of unit malfunction and their corresponding corrective actions.
Lists all error codes displayed by the unit and provides corrective actions for each.
Presents general technical data of the unit, including dimensions, weight, and operating ranges.
Details electrical specifications, including power supply requirements and component ratings.
