What to do if my Daikin FVQ140CVEB Air Conditioner does not operate at all?
If your Daikin Air Conditioner isn't operating, check the following: * Ensure no fuse has blown. Turn off the power supply. * See if the power circuit breaker is blown. Turn the power on with the power circuit breaker switch in the off position. * Check for a power failure. Wait until power is restored.
What to do if water leaks from Daikin Air Conditioner unit?
If water is leaking from your Daikin Air Conditioner unit, stop the operation immediately.
What to do if the ON/OFF switch does not properly work on my Daikin FVQ140CVEB?
If the ON/OFF switch on your Daikin Air Conditioner does not work properly, turn off the main power switch.
What to do if Daikin Air Conditioner detects multiple master units?
If your Daikin Air Conditioner detects multiple master units, connect the remote controller to only one indoor unit.
What to do if Daikin FVQ140CVEB Air Conditioner has gas shortage due to clogging in refrigerant piping?
If you suspect clogging in the refrigerant piping system of your Daikin Air Conditioner, check for a failure to open the stop valve and any clogging within the refrigerant system.
What does excess indoor units connected error mean on Daikin FVQ140CVEB?
This error will be displayed if five or more indoor units are connected to your Daikin Air Conditioner.
Why Daikin FVQ140CVEB unit started or stopped without pressing the on/off button?
If your Daikin Air Conditioner started or stopped without pressing the ON/OFF button: * Verify that the ON/OFF timer operation is not in use. Turn off the ON/OFF timer. * Check if a remote control device is connected. Contact the central control room that directed the stop. * See if the display for centralized control is lit. Contact the central control room that directed the stop.
What to do if a safety device frequently actuates on Daikin FVQ140CVEB?
If a safety device such as a fuse, a power circuit breaker, or an earth leakage breaker frequently actuates on your Daikin Air Conditioner, do not turn on the main power switch.
Why does my Daikin Heat Pump emit an odor?
If your Daikin Heat Pump emits an odor, it's likely due to room smells and cigarette odors that have accumulated inside the indoor unit. To resolve this, the inside of the indoor unit must be cleaned.
General| Brand | Daikin |
|---|---|
| Model | FVQ140CVEB |
| Category | Air Conditioner |
| Language | English |
Guidelines for the proper disposal of electrical and electronic products and batteries according to local and national legislation.
Information on heat pump/cooling only types and group/dual remote control systems.
Details on indoor and outdoor unit components and their functions.
Details on the type of refrigerant and its global warming potential.
Covers warnings on proper operation, handling malfunctions, and avoiding direct hazards.
Precautions for installation, modification, electrical safety, and submersion.
Guidelines on suitable environments and restrictions on use with oil vapor or smoke.
Guidance on selecting appropriate locations and avoiding unsuitable environments.
Requirements for wiring, electrical work, and managing running noises.
Ensuring proper drain piping for complete drainage to prevent issues.
Details on how cooling operation behaves, including frost formation and defrost cycles.
Information on heating operation, start-up delays, and warm air circulation.
Methods for adjusting horizontal airflow direction using the remote controller.
Manual adjustment of vertical airflow direction using flaps.
Instructions on how to clean the air filter and when it needs replacement.
Troubleshooting steps when the system does not start or restart immediately.
Addresses issues like operation stopping, fan speed differences, and airflow direction discrepancies.
Explanations for white mist, noises, and dust blowing from the unit.
Checks for blown fuses, tripped breakers, or power failures before requesting service.
Checks for blocked inlets/outlets or clogged filters when the system stops.
Troubleshooting steps for insufficient cooling/heating due to blockages or improper settings.
Investigates timer operations, remote control conflicts, or centralized control issues.
Actions to take when specific error codes or indicators appear on the display.
To Next Page
