What to do if my Daikin FVQ125CVEB does not operate at all?
If your Daikin Air Conditioner isn't operating, check the following: * Ensure no fuse has blown. Turn off the power supply. * See if the power circuit breaker is blown. Turn the power on with the power circuit breaker switch in the off position. * Check for a power failure. Wait until power is restored.
What to do if water leaks from Daikin Air Conditioner unit?
If water is leaking from your Daikin Air Conditioner unit, stop the operation immediately.
What to do if the ON/OFF switch does not properly work on my Daikin FVQ125CVEB Air Conditioner?
If the ON/OFF switch on your Daikin Air Conditioner does not work properly, turn off the main power switch.
What to do if Daikin Air Conditioner detects multiple master units?
If your Daikin Air Conditioner detects multiple master units, connect the remote controller to only one indoor unit.
What to do if Daikin Air Conditioner has gas shortage due to clogging in refrigerant piping?
If you suspect clogging in the refrigerant piping system of your Daikin Air Conditioner, check for a failure to open the stop valve and any clogging within the refrigerant system.
What does excess indoor units connected error mean on Daikin Air Conditioner?
This error will be displayed if five or more indoor units are connected to your Daikin Air Conditioner.
Why Daikin Air Conditioner unit started or stopped without pressing the on/off button?
If your Daikin Air Conditioner started or stopped without pressing the ON/OFF button: * Verify that the ON/OFF timer operation is not in use. Turn off the ON/OFF timer. * Check if a remote control device is connected. Contact the central control room that directed the stop. * See if the display for centralized control is lit. Contact the central control room that directed the stop.
What to do if a safety device frequently actuates on Daikin Air Conditioner?
If a safety device such as a fuse, a power circuit breaker, or an earth leakage breaker frequently actuates on your Daikin Air Conditioner, do not turn on the main power switch.
Why does my Daikin Heat Pump emit an odor?
If your Daikin Heat Pump emits an odor, it's likely due to room smells and cigarette odors that have accumulated inside the indoor unit. To resolve this, the inside of the indoor unit must be cleaned.
General| Category | Air Conditioner |
|---|---|
| Cooling Capacity | 12.5 kW |
| Heating Capacity | 14.0 kW |
| Power Source | Electric |
| Outdoor Unit Dimensions (HxWxD) | 990 x 940 x 320 mm |
| Refrigerant | R410A |
| Indoor Unit Dimensions (HxWxD) | 235 x 1590 x 690 mm |
| Noise Level (Outdoor) | 49 dB |
| Type | Ceiling Suspended Unit |
Describes heat pump, cooling only, group control, and two remote controller systems.
Lists and describes the components of the indoor and outdoor units.
Explains the meaning of WARNING and CAUTION labels for safety.
Covers potential hazards like exposure to air, refrigerant leaks, improper installation, and electrical safety.
Details suitable and unsuitable places for unit installation, including environmental factors.
Specifies requirements for wiring installation and electrical safety compliance.
Guides on selecting locations to minimize running noise and vibrations.
Emphasizes proper drain piping for complete drainage and preventing water leakage.
Explains cooling operation behavior, including frost formation and DEFROST OPERATION.
Details heating operation, including start-up time and DEFROST OPERATION.
Explains manual and automatic adjustment of left/right airflow flaps.
Details how to adjust airflow direction vertically by hand.
Provides instructions on adjusting horizontal and vertical airflow flaps for optimal comfort.
Details when and how to clean the air filter, including reset procedure.
Explains reasons for system non-operation and normal delays.
Addresses intermittent operation stops and potential causes like noise interference.
Explains why fan speed might not match settings during certain operations.
Covers situations where airflow direction differs from settings or remote control display.
Explains white mist and various operational noises.
Steps to check when the system fails to start, including power and circuit breaker issues.
Checks for blockages or clogged filters when the system stops after completion.
Addresses issues of insufficient cooling/heating, checking for blockages, filters, and settings.
To Next Page
