Daikin MicroTech I - Page 35


www.DaikinApplied.com 35 IM 1285-4 • MICROTECH III

Figure 30: ATV 212 (MD2) Drive Parameters
PART NUMBER REV
PART DESCRIPTION
170632000
B Rooftop - MT3 SAF (set 321) PARAMETERS
Drive Voltage HP Application
ATV21 ALL ALL
SAF/RAF, RT/SC
Code Function Description Unit Min. Value Max. Value
Default
Value
New Value
Logical
Address
AU1
Automatic acceleration/deceleration 1021 0 0
AU4 Automatic function setting 1040 1 40
CMOd Command mode selection 1020 2 3
FMOd Frequency setting mode selection 1 1151 4 4
FMSL Meter selection 1 0 19 0 5
FM Meter adjustment 1 1 1280 145 318 6
tyP Default setting 1090
7
7
Fr Forward/reverse run selection (Operation panel) 1030 8
ACC Acceleration time 1 0.1sec 0,0 3200,0 10 60 9
DEC Deceleration time 1 0.1sec 0,0 3200,0 10 60 10
FH Maximum frequency 0.01Hz 30,00 200,00 50 60 11
UL Upper limit frequency 0.01Hz 0,50 80,00 50 60 12
LL Lower limit frequency 0.01Hz 0,00 60,00 0 20 13
vL Base frequency 1 0.01Hz 25,00 200,00 50 60 14
vLv Base frequency voltage 1 0.1V 50,0 660,0 McQuay load 409
Pt V/F control mode selection 1 1061 15
vb Torque boost 1 0.10% 0,0 30,0 5 16
tHr Motor electronic-thermal protection level 1 1% 10 100 100 600
OLM Electric-thermal protection characteristic selection 1070 1 17
Sr1 Preset-speed operation frequency 1 0.01Hz 0,00 60,00 15 18
Sr2 Preset-speed operation frequency 2 0.01Hz 0,00 60,00 20 19
Sr3 Preset-speed operation frequency 3 0.01Hz 0,00 60,00 25 20
Sr4 Preset-speed operation frequency 4 0.01Hz 0,00 60,00 30 21
Sr5 Preset-speed operation frequency 5 0.01Hz 0,00 60,00 35 22
Sr6 Preset-speed operation frequency 6 0.01Hz 0,00 60,00 40 23
Sr7 Preset-speed operation frequency 7 0.01Hz 0,00 60,00 45 24
F100 Low-speed signal output frequency 0.01Hz 0,00 80,00 0 100
F101 Speed reach setting frequency 0.01Hz 0,00 80,00 0 101
F102 Speed reach detection band 0.01Hz 0,00 80,00 2.5 102
F108 2nd always-active function selection 1 0 71 0 108
F109 Analog/contact input function selection (VIA/VIB) 1020 109
F110 Always-active function selection 1 0 71 1 110
F111 Input terminal selection1 (F) 1 0 71 2 45 111
F112 Input terminal selection 2 (R) 1 0 71 6 0 112
F113 Input terminal selection 3 (RST) 1 0 71 10 113
F118 Input terminal selection 8 (VIA) 1 0 71 7 118
F130 Output terminal selection 1A (RY-RC) 1 0 255 4 14 130
F132 Output terminal selection 3 (FL) 1 0 255 11 132
F137 Output terminal selection 1B (RY-RC) 1 0 255 255 137
F139 Output terminal logic selection (RY-RC/OUT-NO) 1010 139
F167 Frequency command agreement detection range 0.01Hz 0,00 80,00 2.5 167
F170 Base frequency 2 0.01Hz 25,00 200,00 50 60 170
F171 Base frequency voltage 2 0.1V 50,0 660,0 171
F172 Torque boost 2 0.10% 0,0 30,0 5 172
F173 Motor electronic-thermal protection level 2 1% 10 100 100 173
F185 Stall prevention level 2 1% 10 111 110 185
F200 Frequency priority selection 1010 200
F201 VIA input point 1 setting 1% 0 100 0 201
F202 VIA input point 1 frequency 0.01Hz 0,00 200,00 0 202
F203 VIA input point 2 setting 1% 0 100 100 203
F204 VIA input point 2 frequency 0.01Hz 0,00 200,00 50 204
ATV21 MT3 SAF PAGE 1