www.DaikinApplied.com 39 IM 1285-4 • MICROTECH III
Figure 30 continued: ATV 212 (MD2) Drive Parameters
PART NUMBER REV
PART DESCRIPTION
170632000
B Rooftop - MT3 SAF (set 321) PARAMETERS
Drive Voltage HP Application
ATV21 ALL ALL
SAF/RAF, RT/SC
Code Function Description Unit Min. Value Max. Value
Default
Value
New Value
Logical
Address
F706 Free unit display bias
0.01Hz 0,00 80,00 0
706
F707 Free step 1 (pressing a panel key once)
0.01Hz 0,00 80,00 0
707
F708 Free step 2 (panel display)
1 0 255 0
708
F710 Standard monitor display selection
10100
710
F721 Panel stop pattern
1010
721
F730 Prohibition of freq. setting on the operation panel (FC)
1010
730
F732 Panel operation prohibition (Local/Remote keys)
10101
732
F733 Panel operation prohibition (RUN/STOP keys)
1010
733
F734 Prohibition of panel emergency stop operation
1010
734
F735 Prohibition of panel reset operation
1010
735
F738 Selection of AUF
1010
738
F748 Selection of watt hour memory
1011
748
F749 Display unit selection of watt hour
1030
749
F800 Communication band speed
1011
800
F801 Parity
1021
=0; McQuay 801
F802 Inverter number; SAF=1;RAF=2;HW=3
1 0 247 1
=1;McQuay
802
F803 Communication error trip time
1sec 0 100 3 10
803
F805 Communication waiting time
0.01sec 0,00 2,00 0
805
F806 Setting master & slave for comm between inverters
1040
806
F811 Communication input point 1 setting
1% 0 100 0
811
F812 Communication input point 1 frequency
0.01Hz 0,00 200,00 0
812
F813 Communication input point 2 setting
1% 0 100 100
813
F814 Communication input point 2 frequency
0.01Hz 0,00 200,00 0
=60;McQuay 814
F829 Selection of communication protocol
1041
829
F851 Inverter action at network & communication break
10440
851
F856 Number of motor poles for comm speed calculation
1182
856
F870 Block write data 1
1060
870
F871 Block write data 2
1060
871
F875 Block read data 1
10110
875
F876 Block read data 2
10110
876
F877 Block read data 3
10110
877
F878 Block read data 4
10110
878
F879 Block read data 5
10110
879
F880 Free notes
1 0 65535 0 321
880
F890 Parameter for option 1
1 0 65535 0
890
F891 Parameter for option 2
1 0 65535 0
891
F892 Parameter for option 3
1 0 65535 0
892
F893 Parameter for option 4
1 0 65535 0
893
F894 Parameter for option 5
1 0 65535 0
894
F895 Parameter for option 6
1 0 65535 0
895
F896 Parameter for option 7
1 0 65535 0
896
F897 Parameter for option 8
1 0 65535 0
897
F898 Parameter for option 9
1 0 65535 0
898
F899 Parameter for option 10
1 0 65535 0
899
F910 Step-out detection current level (for PM motors)
1% 10 150 100
910
F911 Step-out detection time (for PM motors)
0.1sec 0,0 25,0 0.0
911
F912 q-axis self-inductance (for PM)
0.01mH 0,00 650,00 0.00
912
ATV21 MT3 SAF PAGE 4
To Next Page
Loading...
