Daikin Perfera FTXM-A Series - Hour Countdown OFF;ON Timer Setting; Weekly Timer Operation

5 Operation
Operation manual
11
FTXM60~71A2V1B
Daikin room air conditioner
3P728539-5F – 2024.01
INFORMATION
Each time or is pressed, the time setting
advances by 10 minutes. Holding the button down will
change the setting rapidly.
4 To cancel the timer setting, press .
Result: The set time and disappear from the LCD. and the
day of the week are displayed on the LCD. The Daikin eye stops
lighting orange.
To combine OFF timer and ON timer
1 To set the timers, refer to "To start/stop OFF timer
operation"[410] and "To start/stop ON timer operation"[410].
Result: and are displayed on the LCD.
Example:
Display Current time Set while… Operation
6:00 the unit is
operating.
Stops at 7:00
and starts at
14:00.
the unit is NOT
operating.
Starts at 14:00.
Note: If the timer setting is active, the current time is NOT displayed
on the LCD.
5.9.2 12 hour countdown OFF/ON timer setting
To start/stop countdown OFF/ON timer operation
1 Press and hold or for about 5 seconds;
when blinks, release the button.
Result:
For the OFF timer, appears on the LCD and
blinks, and the day of the week disappear from the
LCD.
For the ON timer, appears on the LCD and
blinks. and the day of the week disappear from the
LCD.
2 Press or to change the time setting. The time can be
set between 1~12hours. Each pressing of the button increases
or decreases the time setting by 1hour.
3 Press or to confirm the setting.
Result: and/or and the set time are displayed on the LCD.
The Daikin eye lights orange. The time displayed on the LCD will
automatically count down by 1 hour for every hour that passes.
Example: If the OFF timer is set to 3hours, the displayed time will
change as follows: 3hr → 2hr → 1hr → blank (OFF)
4 To change the setting back to 24 hour OFF/ON timer, repeat
step 1 when on the home screen when and/or are
NOT blinking.
5 To cancel the timer setting, press .
To combine the timer display modes
Different display modes (24 hour and 12 hour countdown OFF/ON
timer) can be used for the OFF timer and ON timer simultaneously.
1 For setting, see "To start/stop OFF timer operation" [4 10], "To
start/stop ON timer operation" [4 10] and "To start/stop
countdown OFF/ON timer operation"[411].
Example:
Display Current time Set while… Operation
22:00 the unit is
operating.
▪ Stops at 1:00
(3hours after
present time)
▪ Starts at
6:00. (8hours
after present
time)
Note: If the timer setting is active, the current time is NOT displayed
on the LCD.
5.10 Weekly timer operation
INFORMATION
The following setting procedure is for the wireless remote
control only. However, we recommend to perform the
weekly timer setting using the ONECTA app. Refer to
"5.11 Wireless LAN connection" [4 13] for more
information.
With this operation, you can save up to 4 timer settings for each day
of the week.
Example: Create a different setting from Monday to Friday and a
different setting for weekends.
Day of the week Setting example
Monday
▪ Make up to 4settings.
6:00 8:30 17:30
25°C 27°C25°C
22:00
1 2 3 4
ON OFF ON OFF
Tuesday~Friday
▪ Use the copy mode if the
settings are the same as
for Monday.
6:00 8:30 17:30
25°C 27°C25°C
22:00
1 2 3 4
ON OFF ON OFF
Saturday
▪ No timer setting
—
Sunday
▪ Make up to 4settings.
8:00 10:00 19:00 21:00
27°C 27°C25°C
ON OFF OFF ON
1 2 3 4
▪ ON-ON-ON-ON setting. Enables scheduling the operation mode
and set temperature.
▪ OFF-OFF-OFF-OFF setting. Only the turn off time can be set for
each day.
Note: Be sure to aim the wireless remote control at the indoor unit
and check for a receiving tone when setting the Weekly timer
operation.
INFORMATION
The clock MUST be set correctly before using any timer
functions. Refer to "4.3To set the clock"[46].
INFORMATION
▪ Weekly timer and OFF/ON timer operation CANNOT be
used at the same time. The OFF/ON timer operation
takes priority. Weekly timer will be in standby,
disappears from the LCD. When the OFF/ON timer is
completed, the Weekly timer becomes active.
▪ The day of the week, OFF/ON timer mode, time and
temperature (only for ON timer) can be set with the
Weekly timer. Other settings are based on previous ON
timer setting.