Why Daikin RXS35BVMB Air Conditioner is not turning on? (OPERATION lamp is off)
If your Daikin Air Conditioner isn't turning on and the OPERATION lamp is off, check the following: * Ensure the breaker hasn't been turned OFF or a fuse hasn't blown. * Verify that there isn't a power failure. * Confirm that batteries are correctly installed in the remote controller. * Check if the timer setting is correct.
What to do if Daikin RXS35BVMB Air Conditioner operation stops suddenly? (OPERATION lamp is on)
If your Daikin Air Conditioner stops suddenly and the OPERATION lamp is on, it might be due to a sudden large voltage fluctuation. For system protection, the air conditioner automatically resumes operation in about 3 minutes.
Why Daikin RXS35BVMB operation does not start soon?
If your Daikin Air Conditioner doesn't start immediately after pressing the ON/OFF button soon after stopping or reselecting the mode, wait for about 3 minutes.
Why Daikin RXS35BVMB outdoor unit emits water or steam?
The outdoor unit of your Daikin Air Conditioner may emit water or steam. This can occur in HEAT mode when frost on the outdoor unit melts during defrost operation. In COOL or DRY mode, moisture in the air can condense on the cool surface of the outdoor unit piping and drip.
Why is my Daikin RXS35BVMB cooling effect poor?
If the cooling or heating effect of your Daikin air conditioner is poor, consider the following: * Ensure the air filters are clean. * Check for any obstructions blocking the air inlet or outlet of the indoor and outdoor units. * Verify that the temperature setting is appropriate. * Confirm that all windows and doors are closed. * Make sure the airflow rate and direction are set correctly.
How to improve cooling (heating) effect of Daikin Air Conditioner?
If you're experiencing poor cooling or heating with your Daikin Air Conditioner, consider these points: * Ensure the air filters are clean. * Make sure nothing is blocking the air inlet or outlet of the indoor and outdoor units. * Verify that the temperature setting is appropriate. * Confirm that windows and doors are closed. * Check if the airflow rate and direction are set correctly. * Check if the unit is set to the INTELLIGENT EYE mode.
Why my Daikin Air Conditioner smells bad?
If your Daikin Air Conditioner's indoor unit is emitting an odor, it's likely due to smells from the room, furniture, or cigarettes being absorbed into the unit and discharged with the airflow. If this occurs, it is recommended to have the indoor unit cleaned by a technician.
Why Daikin Air Conditioner hot air does not flow out soon after the start of heating operation?
If hot air doesn't flow out immediately after starting the heating operation on your Daikin Air Conditioner, allow 1 to 4 minutes for the system to warm up. The system is designed to discharge air only after reaching a certain temperature.
Why Daikin Air Conditioner heating operation stops suddenly and a flowing sound is heard?
If the heating operation on your Daikin Air Conditioner stops suddenly and you hear a flowing sound, the system is likely removing frost from the outdoor unit. Wait for about 3 to 8 minutes.
Why does Daikin RXS35BVMB Air Conditioner release mists from the indoor unit?
Mists may come out of the indoor unit of your Daikin Air Conditioner when the air in the room is cooled into mist by the cold airflow during cooling operation.
General| Category | Air Conditioner |
|---|---|
| Type | Split System |
| Cooling Capacity | 3.5 kW |
| Heating Capacity | 4.0 kW |
| Weight (Outdoor Unit) | 30 kg |
| Power Supply | 220-240 V, 50 Hz |
| Refrigerant | R32 |
| Outdoor Unit Noise Level | 48 dB |
General safety precautions to be followed before performing repair work.
Safety precautions to be observed after the repair work is completed.
Procedures and checks to be performed after the repair is finished.
Explanation of icons used in the manual to draw attention to specific information.
Lists the functions available for the Cooling Only models.
Lists the functions available for the Heat Pump models.
Technical specifications for Cooling Only models (Indoor and Outdoor units).
Technical specifications for Heat Pump models (Indoor and Outdoor units).
Wiring diagram for the indoor unit's printed circuit boards and connectors.
Wiring diagram for the outdoor unit's printed circuit boards and connectors.
Details on core functions like inverter principle, airflow, fan speed, and operational modes.
Explains the main components and the role of thermistors in system operation.
Covers mode hierarchy, frequency control, start-up controls, discharge pipe, input current, freeze-up, peak-cut, fan, moisture, defrost, expansion valve, malfunctions, forced operation.
General overview of system configuration after installation and test operation.
Covers safety precautions, parts identification, operation modes, adjustments, and special features.
Provides guidance on care, cleaning, and resolving common issues.
Important cautions to consider before performing diagnostic procedures.
Lists common operational problems and their corresponding solutions.
Explains how to use the service check function for error code display.
Comprehensive guide to diagnosing and resolving various system errors.
Procedures for checking key components like EV, Four Way Valve, Thermistors, Installation, Pressure, Fan, Power, Refrigerant, Capacitor, Transistor, Hall IC.
Step-by-step instructions for disassembling indoor unit components like filters, grille, blades, PCB, fan, etc.
Step-by-step instructions for disassembling outdoor unit components like casing, PCB, fan, compressor, valves, etc.
Covers trial operation, jumper settings, and intelligent eye sensor adjustment.
Visual diagrams showing piping and wiring connections for indoor and outdoor units.
To Next Page
