Daikin Siesta ATXF50A2V1B - Powerful Operation; To Start;Stop Powerful Operation; Econo Operation; To Start;Stop Econo Operation

4 Operation
Operation manual
6
ATXF50~71A2V1B
Daikin room air conditioner
3P511999-5G – 2019.12
Result: The flap position will change, is displayed on the
LCD, and the airflow rate is set to automatic.
Mode Position of flap…
Cooling/Drying Up
Heating Down
2 Press to stop.
Result: The flap will return to the position from before the Comfort
airflow mode; disappears from the LCD.
4.6 Powerful operation
This operation quickly maximizes the cooling/heating effect in any
operation mode. You can get the maximum capacity.
INFORMATION
Powerful operation CANNOT be used together with Econo
and Comfort airflow operation. The last selected function
takes priority.
Powerful operation will NOT increase the capacity of the
unit if it already operates at maximum capacity.
4.6.1 To start/stop Powerful operation
1 Press to start.
Result: is displayed on the LCD. Powerful operation runs
for 20minutes; after that, operation returns to the previously set
mode.
2 Press to stop.
Result: disappears from the LCD.
Note: Powerful operation can be set only when the unit is running. If
you press , operation will be cancelled; disappears
from the LCD.
4.7 Econo operation
This is a function which enables efficient operation by limiting the
maximum power consumption value. This function is useful for cases
in which attention should be paid to ensure a circuit breaker will not
trip when the product runs alongside other appliances.
INFORMATION
▪ Powerful and Econo operation CANNOT be used at the
same time. The last selected function takes priority.
▪ Econo operation reduces power consumption of the
outdoor unit by limiting the rotation speed of the
compressor. If power consumption is already low,
Econo operation will NOT further reduce power
consumption.
4.7.1 To start/stop Econo operation
1 Press to start.
Result: is displayed on the LCD.
2 Press to stop.
Result: disappears from the LCD.
4.8 OFF/ON timer operation
Timer functions are useful for automatically switching the air
conditioner on/off at night or in the morning. You can also use OFF
timer and ON timer in combination.
INFORMATION
Program the timer again in case of:
▪ A breaker has turned the unit off.
▪ A power failure.
▪ After replacing batteries in the user interface.
4.8.1 To start/stop ON timer operation
1 Press to start.
Result: is displayed on the LCD and the timer lamp lights
up.
INFORMATION
Each time is pressed, the time setting advances by
1 hour. The timer can be set between 1 to 12 hours.
2 Press to stop.
Result: disappears from the LCD and the timer lamp
goes off.
4.8.2 To start/stop OFF timer operation
1 Press to start.
Result: is displayed on the LCD and the timer lamp lights
up.
INFORMATION
Each time is pressed, the time setting advances by
1 hour. The timer can be set between 1 to 9 hours.
2 Press to stop.
Result: disappears from the LCD and the timer lamp
goes off.
INFORMATION
When you set the ON/OFF timer, the time setting is stored
in the memory. The memory will be reset when the user
interface batteries are replaced.
Use of night set mode in combination with OFF timer
The air conditioner automatically adjusts the temperature
setting (0.5°C up in cooling, 2.0°C down in heating) to
prevent excessive cooling/heating and ensure a
comfortable sleeping temperature.
4.8.3 To combine OFF timer and ON timer
1 To set the timers, refer to "4.8.2 To start/stop OFF timer
operation" [4 6] and "4.8.1 To start/stop ON timer
operation"[46].
Result: and are displayed on the LCD.
2 Example of what is displayed on the LCD if you combine the 2
timers: