To Next PageTo Next PageWhat to do if my Danby Kitchen Appliance has no power?
If your Danby Kitchen Appliance has no power, a fuse in your home may be blown, the circuit breaker tripped, or the plug may not be fully inserted into the wall outlet. To resolve this, replace the fuse or reset the circuit breaker. You can also unplug the appliance, wait a few seconds, and then plug it back in. Make sure the 3-prong plug is fully inserted into the outlet.
Why is the cabinet temperature too high in my Danby Kitchen Appliance?
If your Danby Kitchen Appliance's cabinet temperature is too high, it could be due to the temperature being set too high, the door not being shut properly or being opened excessively, an obstructed exhaust vent, or recently adding a large quantity of warm beverages to the cabinet. Verify the temperature control setting and adjust if necessary. Ensure that the door is fully closed and that the gasket is sealing against the cabinet. Open the doors only as needed and for short periods. Verify there is nothing blocking the front mounted exhausting vent. Limit the quantity of warm beverages being introduced to the cabinet at the same time; attempt to stagger the load introduction if possible.
What to do if my Danby Kitchen Appliance is beeping and “HI” is displayed?
If your Danby Kitchen Appliance is beeping and "HI" is displayed on the control panel, it could be because you recently added a large quantity of warm bottles or cans to the cabinet, the door is not closed tightly, or there is a system leak, evaporator fan failure, or compressor fan failure. To solve this, limit the quantity of warm items being introduced to the cabinet and be sure the door is closed tightly. To stop the beeping, unplug the unit.
Why is there condensation on my Danby Kitchen Appliance?
Condensation on the cabinet and/or doors of your Danby Kitchen Appliance is usually caused by high humidity conditions in the home or the door not being shut properly or opened excessively. The condensation will subside once humidity conditions return to normal. Ensure that the door is fully closed and that the gasket is sealing against the cabinet. Open the door only as needed and for short periods of time.
What does it mean if my Danby Kitchen Appliance is beeping and “LO” is displayed?
If your Danby Kitchen Appliance is beeping and “LO” is displayed in the control panel, it is due to sensor failure, or the evaporator temperature being too low. To stop the beeping, unplug the unit.
General| Type | Beverage Center |
|---|---|
| Capacity | 3.1 cu. ft. |
| Finish | Stainless Steel |
| Refrigerant | R600a |
| Installation | Freestanding |
| Door Finish | Stainless Steel |
| Voltage | 115V |
| Color | Stainless Steel |
| Temperature Range | 2°C - 10°C (36°F - 50°F) |
Key warnings regarding appliance usage, child safety, and electrical hazards.
Essential electrical specifications and safety precautions for connection.
Detailed steps and warnings for properly grounding the appliance.
Explicitly states not to use extension cords for safe operation.
Steps to ensure the beverage centre is level for optimal performance.
Guidance on choosing the best placement for the beverage centre.
Preparing the surrounding cabinet or space for the beverage centre.
Identification and brief description of the beverage centre's key features.
Explanation of the control panel buttons and indicators.
How to adjust and switch between Celsius and Fahrenheit temperature settings.
Details on door ajar alarm, temperature memory, and temperature alarms.
Information on maximum capacity and proper storage of beverages.
Instructions on how to remove and manage the glass shelves.
Step-by-step guide to reversing the door swing direction of the unit.
Detailed steps for cleaning the interior and exterior surfaces of the appliance.
Guidance on what to do during a power outage to protect contents.
Procedures for safely moving the beverage centre.
Steps to resolve issues when the unit does not turn on.
How to address high temperature alarms and the 'HI' indicator.
How to address low temperature alarms and the 'LO' indicator.
Causes and solutions for condensation forming on the unit.
Explains the duration and coverage of the warranty for different parts.
Instructions on how to contact customer service or a service depot for repairs.
Lists conditions and situations not covered by the warranty.
Contact information for obtaining warranty service.
