Dansons Group Pit Boss Mahogany PB1000D3 User Manual (English)

Questions and Answers:

J
Jose Avila MDAug 18, 2025
What to do if my Dansons Group Grill has no power lights on the control board?
- C
  Cody BoydAug 18, 2025
  If there are no power lights on the control board of your Dansons Group Grill, first, ensure the unit is plugged into a working power source and reset the breaker. Also, check that the GFCI is a minimum 10 Amp service. Make sure all wire connections are firmly connected and dry. Then, press the Power Button, ensuring it glows blue, and turn the Temperature Control Dial to a temperature setting. If the issue persists, the fuse on the control board may be blown and needs replacement, or the control board itself might be faulty.
S
stevenmccoyAug 20, 2025
Why my Dansons Group Pit Boss Mahogany PB1000D3 will not achieve or maintain stable temperature?
- L
  Lisa GoodwinAug 21, 2025
  If your Dansons Group Grill isn't maintaining a stable temperature, there could be several reasons. First, check the burn pot for ash build-up or obstructions and ensure the fan is working correctly with no blockage in the air intake. Also, verify sufficient fuel levels and quality, ensuring no obstructions in the feed system. Check the grill probe for dirt. After these steps, start the grill, set it to SMOKE, wait 10 minutes, and check if the flame produced is bright and vibrant.
A
Alicia WhitakerAug 23, 2025
What to do if the fire in burn pot will not light in my Dansons Group Pit Boss Mahogany PB1000D3 Grill?
- N
  nathan72Aug 25, 2025
  If the fire in the burn pot of your Dansons Group Grill won't light, it might be due to several reasons. First, ensure the auger is primed, especially if it's the first use or the hopper was completely emptied. Check if the auger motor is jammed and confirm that the auger is dropping pellets into the burn pot. Inspect the igniter to make sure it's working and protruding approximately 13mm / 0.5 inches into the burn pot. Lastly, check the burn pot for ash build-up or obstructions and ensure sufficient airflow.
M
Monica VangAug 26, 2025
Why does my Dansons Group Pit Boss Mahogany PB1000D3 produce excess or discolored smoke?
- M
  maddoxsamanthaAug 26, 2025
  Excess or discolored smoke from your Dansons Group Grill can be due to grease build-up, poor wood pellet quality, a blocked burn pot, or insufficient air intake for the fan. Remove moist wood pellets and replace them with dry ones. Clear the burn pot of ash and debris. Ensure the fan is working correctly and the air intake is not blocked.
B
brownmatthewAug 28, 2025
What does ErH error code mean on my Dansons Group Grill and how to fix it?
- J
  Jeffery ColonAug 28, 2025
  The ErH error code on your Dansons Group Grill indicates that the unit has overheated, possibly due to a grease fire or excess fuel. To resolve this, press the Power Button to turn the unit off and allow the grill to cool. After it cools down, remove the pellets and confirm the positioning of all component parts. Then, press the Power Button again and select your desired temperature.
A
Andre ValentineAug 31, 2025
How to prevent frequent flare-ups on my Dansons Group Pit Boss Mahogany PB1000D3?
- J
  Jessica HughesAug 31, 2025
  To prevent frequent flare-ups on your Dansons Group Grill, try cooking at a lower temperature, especially when cooking highly greasy food (keep the temperature under 176°C / 350°F). Also, ensure that you regularly clean the cooking components to prevent grease build-up.
C
Charles CooperSep 2, 2025
What does it mean when the temperature is flashing on the LCD screen of my Dansons Group Grill?
- J
  Justin StevensSep 2, 2025
  A flashing temperature on the LCD screen of your Dansons Group Grill indicates that the grill temperature is below 65°C / 150°F. This suggests there's a risk the fire could go out. Check the hopper for sufficient fuel or any obstructions in the feed system. Inspect the grill probe, burn pot, and fan for any issues like ash build-up or blockages. Also, check the auger motor to confirm it's rotating and there's no blockage in the auger tube.
S
Sarah CervantesSep 5, 2025
What does noP error code mean on my Dansons Group Pit Boss Mahogany PB1000D3?
- M
  Miranda CollinsSep 5, 2025
  The noP error code on your Dansons Group Grill indicates a problem with the meat probe connection. Try disconnecting the meat probe from the connection port on the Control Board and reconnecting it, ensuring the adapter is firmly connected. Check for any damage to the adapter end or the wires of the meat probe. If the issue persists, the control board might be faulty.
K
Kristin HamiltonSep 7, 2025
What does Er1 error code mean on my Dansons Group Grill and how to fix it?
- S
  Savannah EvansSep 7, 2025
  The Er1 error code on your Dansons Group Grill indicates that the grill probe wire is not making a connection. To fix this, check for any damage to the grill probe wires. Also, ensure the grill probe molex connectors are firmly connected, and connected correctly, to the Control Board.
A
Anthony LinSep 9, 2025
What to do if grill temperature on SMOKE is too high on my Dansons Group Grill?
- A
  Andrew RodriguezSep 9, 2025
  If the grill temperature on SMOKE is too high on your Dansons Group Grill, it means that the P Setting is too LOW. To solve the issue, push the "P" SET button, and increase the "P" setting.

Dansons Group Pit Boss Mahogany PB1000D3 Specifications

General

Type	Pellet Grill
Temperature Range	180°F to 500°F
Fuel Type	Wood Pellets
BTU Value	25, 000 BTU
Material	Steel
Digital Control	Yes
Wheels	Yes
Warranty	5 Years
Cooking Area	1000 sq in