Dataprobe iBootBar User Manual

Technical Support Hotline: (201) 934-5111 tech@dataprobe.com
Main: 201-934-9944 Website: dataprobe.com
Scope of this Document:
This document covers the installation and operations of Dataprobe’s iBootBar series of remote power control units.
The following models are covered in this document:
Model Power Feed / Total Capacity Outlets Control
iBB-N15
NEMA 15 Amp 8 x NEMA 5-15 IP Control, Serial Control
iBB-N15-M
NEMA 15 Amp 8 x NEMA 5-15 IP Control, Serial Control, Internal Modem
iBB-2N15
2 x NEMA 30 Amp 8 x NEMA 5-15 IP Control, Serial Control
iBB-2N15-M
2 x NEMA 30 Amp 8 x NEMA 5-15 IP Control, Serial Control, Internal Modem
iBB-N20
NEMA 20 Amp 8 x NEMA 5-15 IP Control, Serial Control
iBB-N20-M
NEMA 20 Amp 8 x NEMA 5-15 IP Control, Serial Control, Internal Modem
iBB-2N20
2 x NEMA 40 Amp 8 x NEMA 5-15 IP Control, Serial Control
iBB-2N20-M
2 x NEMA 40 Amp 8 x NEMA 5-15 IP Control, Serial Control, Internal Modem
iBB-C10
IEC C14 10 Amp 8 x IEC C13 IP Control, Serial Control
iBB-C10-M
IEC C14 10 Amp 8 x IEC C13 IP Control, Serial Control, Internal Modem
iBB-2C10
2 x IEC C14 20 Amp 8 x IEC C13 IP Control, Serial Control
iBB-2C10-M
2 x IEC C14 20 Amp 8 x IEC C13 IP Control, Serial Control, Internal Modem
iBB-C20
IEC C20 20 Amp 8 x IEC C13 IP Control, Serial Control
iBB-C20-M
IEC C20 20 Amp 8 x IEC C13 IP Control, Serial Control, Internal Modem
iBB-2C20
2 x IEC C20 40 Amp 8 x IEC C13 IP Control, Serial Control
iBB-2C20-M
2 x IEC C20 40 Amp 8 x IEC C13 IP Control, Serial Control, Internal Modem
iBootBar
Installation and Operations
Version 1.20
Ref: iBootBar_v1.20

Dataprobe iBootBar Specifications

General

Power Input	100-240 VAC, 50/60 Hz
Network Interface	10/100 Ethernet
Voltage Rating	100-240 VAC
Power Consumption Monitoring	Yes
Remote Reboot Capability	Yes
Dimensions (Rackmount)	1U
Outlets	8
Control Method	Web, SNMP, Telnet
Mounting	Rackmount
Protocols	HTTP, HTTPS, SNMP, Telnet, DHCP
Input Power Cord Length	6 feet
Operating Temperature	0 to 40°C
Humidity Range	5% to 95% non-condensing

Summary

Important Safety Information

Quick Start

Installation

Rack Mounting

Ethernet Port

Serial Port

Configuration

Setup Utility

Introduces the iBootBar Setup and Control Utility (SCU) for finding and configuring devices.

Command Line Interface

Explains how to configure the iBootBar using Telnet, serial port, or dial-up modem via CLI.

Basic Operation

Web Interface

Details the web interface for operating outlets and monitoring unit status with mouse clicks.

Advanced Operations

AutoPing Feature

Firmware Upgrades

Password Recovery

iBootBar Setup and Control Utility

Details the SCU's capabilities for installation, configuration, and management of iBootBars.

Specifications