Dea TEO 700 - Product Description and Transport; Models and Package Contents; Transport and Handling; Technical Specifications

10
2 PRODUCT DESCRIPTION
Models and contents of the package
Under the name TEO 700 is identied a family of 24V electromechanical operators with built-in control board for adjusting the forces
while opening/closing and for managing optional features such as photocells, automatic closing, etc. .. Functions OPEN - CLOSE - STOP
operated by a single key, change of direction when an obstacle is detected in closing, led courtesy light in opening and closing with auto-
off after 3 minutes, protective functions for inputs in low and high voltage, short circuit, etc. .
TEO 700 is an electromechanical operator for the automation of sectional, overhead counterweight and spring doors. It is basically
made up of a mechanical operator rotating the draft gear that, through a chain, transmits the movement directly to the door draft system
thus moving it.
Inspect the “Content of the package” (Pic. 1) and compare it with your product for useful consultation during assembly.
Transport
TEO 700 is always delivered packed in boxes that provide adequate protection to the product, however, pay attention to all informa-
tion that may be provided on the same box for storage and handling.
3 TECHNICAL DATA
TEO 700
CONTROL BOARD OPERATOR
Power supply (V) 230 V ~ ±10% (50/60 Hz) Motor power supply voltage (V) 24 V
Rated power transformer (VA) 100 VA (230/22V) Absorbed power (W) 100
Fuse F2 (A) (transformer) 2,5A 250V Max Thrust (N) 1000
Auxiliaries power supply output +24 V
max 200mA Work cycle (cycles/hour) 15
Flashing light output 24 V
max 15W Maximum n° of operations in 24 hour 35
Receiver frequency 433,92 MHz Operating temperature range (°C) -20÷50
Transmitters type of coding HCS rolling code Opening speed (m/min) 9
Max remote controllers managed 20 Weight of product with package (Kg) 4,3
Protection degree IP30
4 INSTALLATION AND ASSEMBLY
4.1 For a satisfactory installation of the product is important to:
• Ensure the door frame is solid and suitable to be driven;
• Make sure that during its movement it doesn’t present friction points;
• Check it is well balanced. If required adjust the balancing mechanisms;
• Foresee an adequately protected 230V socket near the automation.
4.2 Dened and satised these prerequisites, proceed to the assembly:
• Assemble the track (2) to the main unit (1) by inserting the motor pin inside the pinion (Picture 3);
• Fix the track to the main unit by using the two supports (3);
• Mount the angular support bracket (4) and x it with the xing support (we suggest to keep it as close as possible to the main unit);
Warning: bigger is the distance of the angular support from the main unit, smaller is the part of track available.
• Combine the angular support with the two ceiling xing brackets (5) (adjust the brackets so that the track, once xed, is perfectly horizontal);
• Fix the front bracket (6) to the track fork;
• Mount the release blade (8) on the release base (7) positioned on the track and x it with the 4 screws provided (Picture 4);
• Secure the track to the door frame (if possible) or to the wall with screws or bolts suitable to the material respecting a distance of at least
40mm. from the maximum door stroke;
• Lift the main unit and x it to the ceiling by using proper tools for the material/surface (Picture 5);
• Combine the straight lever (9) with the curved one (10) and x them to the release blade;
• Combine the connecting bracket (11) to the curved lever and then secure them on the top side of the door to be moved by using proper
tools for the material/surface;
Warning: Once the connecting bracket is mounted on the door, the curved lever must be horizontally positioned;
• If the chain get loose, tighten the nut on the front side and adjust tension without overdoing (Picture 6);
4.3 How to unlock the operator
All TEO 700 models are equipped with a release device that is activated by pulling down on the handle shown in Pic. 7, now if no
obstructions hinder its movement, the door can now move freely. The door will be locked again automatically with the rst travel thus
returning the operator to its normal working conditions.