Dell EMC VEP4600 - Page 29

7. The device will reboot.
8. Commands to confirm the firmware was updated:
[root@localhost]# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp2s0f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:40 brd ff:ff:ff:ff:ff:ff
3: enp2s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:41 brd ff:ff:ff:ff:ff:ff
4: enp2s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:42 brd ff:ff:ff:ff:ff:ff
6: enp2s0f3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:43 brd ff:ff:ff:ff:ff:ff
8: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen
1000
link/ether 54:bf:64:be:08:44 brd ff:ff:ff:ff:ff:ff
inet 100.67.144.132/24 brd 100.67.144.255 scope global noprefixroute dynamic enp4s0
valid_lft 542sec preferred_lft 542sec
inet6 fe80::56bf:64ff:febe:844/64 scope link noprefixroute
valid_lft forever preferred_lft forever
9: enp23s0f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:3c:b9:90 brd ff:ff:ff:ff:ff:ff
10: enp23s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:3c:b9:91 brd ff:ff:ff:ff:ff:ff
12: enp23s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:3c:b9:92 brd ff:ff:ff:ff:ff:ff
13: enp23s0f3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:3c:b9:93 brd ff:ff:ff:ff:ff:ff
19: enp101s0f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:38:8c:90 brd ff:ff:ff:ff:ff:ff
20: enp101s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:38:8c:91 brd ff:ff:ff:ff:ff:ff
21: enp101s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:38:8c:92 brd ff:ff:ff:ff:ff:ff
22: enp101s0f3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether e4:43:4b:38:8c:93 brd ff:ff:ff:ff:ff:ff
23: enp181s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default
qlen 1000 – (Updated x710)
link/ether 54:bf:64:be:08:45 brd ff:ff:ff:ff:ff:ff
24: enp181s0f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default
qlen 1000
link/ether 54:bf:64:be:08:46 brd ff:ff:ff:ff:ff:ff
25: enp181s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:47 brd ff:ff:ff:ff:ff:ff
26: enp181s0f3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group
default qlen 1000
link/ether 54:bf:64:be:08:48 brd ff:ff:ff:ff:ff:ff
9. Run the following command to check the version:
[root@localhost]# ethtool -i enp101s0f0
driver: i40e
version: 2.6.12
firmware-version: 6.80 0x80003d74 18.8.9 – (confirmed FW has been updated)
Upgrade rNDC Firmware workaround
29