Dell PowerEdge 2850 - Page 6

Table B-1.SupportedEscapeSequences
After creating macros for the keys listed in TableB-1, press <F1> on the client system's keyboard during terminal emulation to send the escape sequence
<Esc><O><P> to the host system. The host system then interprets the sequence as <F1>.
Additional escape sequences may be required by certain utilities or functions on the host system. Create macros for the additional sequences listed in TableB-
2.
Table B-2. Additional Escape Sequences
NOTE: When creating macros in HyperTerminal, press <Insert> before <Esc> to signify that you are sending an escape sequence rather than escaping
out of the dialog box. If you do not have this function, you must upgrade HyperTerminal.
NOTE: Escape-sequence key combinations listed in TableB-1 are case-sensitive. For example, to generate the character <A> you must press
<Shift><a>.

Key(s)

Supported Sequence

Terminal Emulation
<Up arrow>
<Esc><[><A>
VT 100/220, ANSI
<Down arrow>
<Esc><[><B>
VT 100/220, ANSI
<Right arrow>
<Esc><[><C>
VT 100/220, ANSI
<Left arrow>
<Esc><[><D>
VT 100/220, ANSI
<F1>
<Esc><O><P>
VT 100/220, ANSI
<F2>
<Esc><O><Q>
VT 100/220, ANSI
<F3>
<Esc><O><R>
VT 100/220, ANSI
<F4>
<Esc><O><S>
VT 100/220, ANSI
<F5>
<Esc><O><T>
VT 100, ANSI
<F6>
<Esc><O><U>
VT 100, ANSI
<Esc><[><1><7><~>
VT 100/220
<F7>
<Esc><O><V>
VT 100, ANSI
<Esc><[><1><8><~>
VT 100/220
<F8>
<Esc><O><W>
VT 100, ANSI
<Esc><[><1><9><~>
VT 100/220
<F9>
<Esc><O><X>
VT 100, ANSI
<Esc><[><2><0><~>
VT 100/220
<F10>
<Esc><O><Y>
VT 100, ANSI
<Esc><[><2><1><~>
VT 100/220
<F11>
<Esc><O><Z>
VT 100, ANSI
<Esc><[><2><3><~>
VT 100/220
<F12>
<Esc><O><A>
VT 100, ANSI
<Esc><[><2><4><~>
VT 100/220
<Home>
<Esc><[><1><~>
<Esc><h>
VT 220
ANSI
<End>
<Esc><[><4><~>
VT 220
<Esc><k>
ANSI
<Delete>
<Esc><[><3><~>
VT 220
<Esc><–>
ANSI
<Delete>
<Esc><[><3><~>
VT 220
<Esc><–>
ANSI
<Page Up>
<Esc><[><5><~>
VT 220
<Esc><Shift><?>
ANSI
<Page Down>
<Esc><[><6><~>
VT 220
<Esc></>
ANSI
<Shift><Tab>
<Esc><[><Z>
VT 100
<Esc><[><0><Z>
VT 220
<Esc><[><Shift><z>
ANSI
NOTE: Escape-sequence key combinations listed in TableB-2 are case-sensitive. For example, to generate the character <A> you must press
<Shift><a>.

Key(s)

Supported Sequence
<Ctrl><Alt><Del>
(Reboot host system)
<Esc><R><Esc><r><Esc><R>
<Alt><x>
<Esc><X><X>