Dell PowerEdge R200 Install Guide

www.dell.com | support.dell.com
About Cautions
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Installing the DRAC 4/P
NOTICE: Read these installation instructions before installing your DRAC 4/P expansion card.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the
online or telephone service and support team. Damage due to servicing that is not authorized by Dell is
not covered by your warranty. Read and follow the safety instructions that came with the product.
This document provides special instructions for installing the Dell™ Remote Access Controller 4/P
(DRAC 4/P) card into a Dell PowerEdge™ system.
CAUTION: To help prevent damage to the DRAC 4/P card, ensure that the system is unplugged from its
AC power source before installing the card.
1
Shutdown the system and unplug it from its AC power source.
Your system’s
Product Information Guide provides a sequence of safety steps that you should
perform before opening the cover of your system, including turning off the system and
disconnecting it from its AC power source. However, the DRAC 4/P card can be damaged if it
is installed in the system that is turned off, but still attached to its AC power supply. Ensure
that the system is unplugged from its AC power supply before installing the DRAC 4/P card.
2 Open the system. See "Opening the System" in the Installation and Troubleshooting Guide for
instructions.
3 Determine which expansion slot is most appropriate for the DRAC 4/P card.
Ideally, the DRAC 4/P card should be installed in the PCI expansion slot nearest the RAC
connector on the system board. See "System Board Connectors" in "Jumpers, Switches, and
Connectors" in the
Installation and Troubleshooting Guide for an illustration of your system
board’s connectors.
4 Connect the DRAC 4/P card interface cable from the card to the system’s RAC connector on
the system board. See Figure 1.
NOTE: The interface cable and connectors are keyed and can be connected only one way.
5
Install the DRAC 4/P card into expansion slot:
a Position the DRAC 4/P card so that the card-edge connector aligns with the system-board
card connector on the system board. See Figure 1.
September 2004

Dell PowerEdge R200 Specifications

General

Tcase	72.4 °C
Bus type	FSB
Stepping	C0
FSB Parity	No
Processor code	SLAPM
Processor cache	6 MB
Processor cores	2
Processor model	E3110
System bus rate	- GT/s
Processor series	Intel Xeon 3100 Series
Processor socket	LGA 775 (Socket T)
Processor codename	Wolfdale
Execute Disable Bit	Yes
Motherboard chipset	Intel® 3200
Processing Die size	107 mm²
Processor frequency	3 GHz
Processor cache type	L2
Processor lithography	45 nm
Processor system type	Up
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	1333 MHz
Processor operating modes	64-bit
Thermal Design Power (TDP)	65 W
Processor core voltage (AC)	1.225 - 0.956 V
Number of processors installed	1
CPU multiplier (bus/core ratio)	9
Number of Processing Die Transistors	410 M
HDD capacity	750 GB
HDD interface	Serial ATA
Total storage capacity	1500 GB
Internal memory	2 GB
Internal memory type	DDR2-SDRAM
Memory layout (slots x size)	2 x 1 GB
Maximum graphics card memory	32 MB
Drive bays	2 x 3.5” SATA/SAS
Graphics card	ES1000
USB 2.0 ports quantity	4
Ethernet LAN (RJ-45) ports	0
PCI Express x8 slots	3
Bundled software	OpenManage
Chassis type	Rack (1U)
Storage temperature (T-T)	-40 - 65 °C
Operating temperature (T-T)	10 - 35 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	20 - 80 %
Processor ARK ID	34694

Weight and Dimensions

Depth	5431 mm
Width	4470 mm
Height	427 mm